Whirlpool M-17 Скачать руководство пользователя страница 9

Страница: 9 / 88

GENERAL INFORMATION (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

1-5

Insert the Dual-Filter Assembly into the circular opening in

the fine-filter plate.

Slowly rotate the filter clockwise until it drops into place.

Continue to rotate until the filter is locked into place. If the

filter is not fully seated (still turns freely), continue to run the

filter clockwise until it drops and locks into place.

NOTE:

The Dual-Filter Assembly arrow does not have to align

with the arrow in the fine-filter plate as long as the filter is

locked.

IMPORTANT:

To avoid damage to dishwasher, do not operate

your dishwasher without the filters properly installed. Be sure

the fine-filter plate is securely in place, the Dual-Filter Assembly

does not turn freely, and is locked into place.

New Components/Features

Tub - Taller tub for the largest place setting on the market.

Less room underneath the unit to access components for

service.

TLR - Third level rack option with it’s own wash system.

Rear feed tube with four wash zones.

Spray Arms - It has new attachment method and comes with

compressed size.

Four Legs - Made of plastic similar to dryer legs.

Improved anchoring - Four anchor locations in top tub collar

to top mount the dishwasher under the counter-top.

New small screw head on anchor screws to fit into smaller

side anchor holes in side of tub collar.

Diverter motor - The function of leak detection alerts the

customer to call service.

New installation/service cycle can be activated after the

installation to test the leaks for approximately 5 minutes.

O error code alarm activates if the installer forgets to turn

on the water valve.

Improved diagnostics - Diagnose with more faults/error codes,

some will be displayed to customers.

Flood/Water leak detection - Drip tray and float are present to

catch leaks from under the tub lip or corners. Leak detection

shuts unit off and turns on drain pump and alerts the

customer to call service.

Flow meter - It measures water volume against flow rate.

Tub LED’s - Bar LED’s incorporated into Third Level Rack

support.

Terminal box - New terminal box comes with screws. No wire

nuts are present in terminal box.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды