Whirlpool M-17 Скачать руководство пользователя страница 25

Страница: 25 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-5

Service Error Codes (Continued)

FUNCTION CODE ERROR CODE

CAUSES

WHAT TO CHECK

4 - Heating

2 - Heater relay

stuck open or

heater open

˗ Open connection in heater circuit

Heater component open

Heater drive circuit on control

NOTE:

Control will continue running

cycles with no heat without alerting

customer if this fault is detected.

1. Unplug dishwasher or disconnect power.

Measure resistance of heater and all components

and connections in water heating circuit/heat dry

circuit. Fix/replace open connection/part.

3 - Heater relay

stuck closed or

heater failed

˗ Heater relay on control shorted

Heater component shorted to

ground

NOTE:

Control will continue running

cycles with no heat without alerting

customer if this fault is detected.

1. Unplug dishwasher or disconnect power.

2. Inspect heater and connections for overheating/

shorting. If evidence of overheating or shorts

exists, replace.

Measure resistance of heater and all components

and connections in water heating circuit/heat dry

circuit. Fix/replace open connection/part.

5 - Door Switch

1 - Door stuck

open

Door was not latched within 4 seconds

of pressing the Start/Resume key.

Instruct customer. Refer to

Owner's Manual

Loose connection in door switch

circuit and/or door switch contacts

stuck open and/or door switch not

making contact.

˗ Sloppy door latch assembly

(Can be aggravated by high door

closure force keeping strike plate

from fully seating)

˗ Door switch high resistance

1. Check strike plate and door closure force. Verify

door seal is seated properly. Check for interference

between dish racks and door. Try bending strike

plate down for better engagement.

2. Unplug dishwasher or disconnect power.

3. Check resistances of door switch contacts and all

connections in the door switch circuit with meter,

while opening and closing the door latch.

˗ If high resistance with door closed, check/fix

loose connections.

Measure resistance of door switch contacts while

checking mechanical operation of latch assembly.

Check for broken plastic pieces on latch assembly.

Replace latch if faulty.

If none of the above

1. With door open, verify 13 VDC present across

P12-9 and P12-11.

2. If no voltage present, unplug dishwasher or

disconnect power and replace control.

2 - Door stuck

closed

Control programmed to not start if

it suspects the door switch is stuck

closed. Control looks for the door

switch to open between cycles.

˗ Customer didn't open the door

between cycles or door switch

contacts stuck closed.

1. Open and close the door, select cycle, the press

Start/Resume key. If cycle starts, instruct customer

to open the door between cycles.

2. Unplug dishwasher or disconnect power.

Measure resistances of door switch contacts while

checking mechanical operation of latch assembly.

Fix/replace faulty components.

6 -

Communication

1 - UI does

not get

communication

from main

control

User interface has power but cannot

communicate with main control board.

˗ Loose connection between UI and

main control

˗ Terminal or wire broken in harness

between UI and main control

˗ Main control communication circuit

failed

1. Unplug dishwasher or disconnect power.

2. Check connections between P1 on main control

and user interface. Reconnect, repair, or replace

harness.

3. If harness connections are all good, replace main

control board.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды