Whirlpool M-17 Скачать руководство пользователя страница 35

Страница: 35 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-15

Troubleshooting Guide (Continued)

CUSTOMER DESCRIPTION

POTENTIAL CAUSES

CHECK

RELATED

ERROR

CODES

Poor wash

Diverter disk in sump is missing or wrong

diverter disc installed.

1. Remove lower spray arm, rear

feedtube, and outlet cover and verify

whether the diverter disk is installed.

2. This model should have a 2 hole

diverter disc. If 1 hole disc is installed,

replace.

Heating problem

Refer to “

Service Error Codes

” table.

F4E2

F4E3

Control is programmed to stop cycle and

alert customer when certain fault codes

have been detected.

1. Press Cancel key once to silence alarm

during fault mode.

Read error code from the dishwasher

and refer to “

Service Error Codes

” table.

3. Use service diagnostics mode to get

fault history from appliance.

F1E1

F7E1

F7E2

F8E1

F8E4

F8E5

F9E1

F10E5 (FAE5)

Poor dry

Customer not using rinse aid and/or

dispenser empty

Check rinse aid level in dispenser. Instruct

customer how to fill and monitor level of

rinse aid.

Customer not using Heated Dry option

Recommend use of Heated Dry or

Extended Dry to customer.

Rinse aid dispenser problem

Refer to “

Service Error Codes

” table.

F10E1 (FAE1)

Fan problem

Refer to “

Service Error Codes

” table.

F10E3 (FAE3)

Heating problem

Refer to “

Service Error Codes

” table.

F4E2

F4E3

Control is programmed to stop cycle and

alert customer when certain fault codes

have been detected.

Press Cancel key once to silence alarm

during fault mode. Read error code from

the dishwasher and refer to “

Service Error

Codes

” table. Use service diagnostics

mode to get fault history from appliance.

F1E1

F7E1

F7E2

F8E1

F8E4

F8E5

F9E1

F10E5 (FAE5)

Sanitized LED blinks or

incomplete sanitization

message at end of cycle

(Control could not confirm

sanitization achieved)

Door opened during final rinse or dry

Instruct customer

Incoming water under 84°F (29°C)

Ensure dishwasher is connected to the

hot water supply.

2. Confirm temperature at sink.

Recommended is 120°F (49°C).

3. Unplug dishwasher or disconnect

power and check all connections and

measure resistance in temperature

sensing circuit. Reconnect and/or

replace parts.

Heating problem

Refer to “

Service Error Codes

” table.

F4E2

F4E3

Thermistor/OWI sensor problem

Refer to “

Service Error Codes

” table.

F3E1

F3E2

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды