Whirlpool M-17 Скачать руководство пользователя страница 47

Страница: 47 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-9

Door Switch Circuit

Perform the following checks if the dishwasher does not detect

the door open or closed. This test will check the wiring to the

door switch and the door switch itself. The following items are

part of the door switch circuit:

Harness/Connection

Door Switch/Latch Assembly

Control Board

Test Procedure

Check for improper installation of the dishwasher or leveling.

Check door latch mechanism for obstructions or binding.

Verify door seal is seated properly.

Check for interference between dish racks and door. Repair as

necessary.

Unplug dishwasher or disconnect power.

Remove outer door panel to access door latch and remove

toe and access panels to access control board.

Strip Circuit - Door Switch

Check door switch contacts and all connections in the door

switch circuit. Visually check that the P12 connector on the

control and the door latch connector are securely installed.

If visual check passes, go to step 5.

If any of the connectors are not inserted properly,

reconnect and retest door latch/switch.

Disconnect connector P12 from the control board.

Using an ohmmeter, measure across P12, pins 9 and 11 with

the door closed, strike completely in latch mechanism (switch

closed).

If 3 ohms or less is measured, proceed to step 7.

If high resistance is measured when door is closed, check

for loose connections and repair as needed.

Using an ohmmeter, measure across P12, pins 9 and 11 with

the door open, strike removed from latch mechanism (switch

open).

If reading is infinite, go to step 8.

If reading shows continuity, or door switch is damaged,

replace door switch and retest.

10.

Set voltmeter to DC and connect red lead to test-pad P11-7

(13 V) and black lead to P10-2 (DC GND) on the control board.

11.

Plug in dishwasher or reconnect power and with door open,

verify that 13 VDC is present across P11-7 and P10-2.

If 13 VDC is not present, replace the control and retest.

If 13 VDC is present, proceed to step 10.

12.

Reconnect P12 to control board and perform Diagnostics

Cycle to verify operation.

13.

Unplug dishwasher or disconnect power.

14.

Reassemble all parts and panels.

15.

Plug in dishwasher or reconnect power.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Electronic Control

Micro Pin

K502

Motor (N) Relay

K505

Heater (L1) Relay

K503

Pilot (L1) Relay

K504

Heater (N) Relay

N.O.

(To Wash Motor)

(To Heater)

(To Wash Motor,

Vent, and Triac Loads)

(To Heater)

N.O.

Door

Switch

Sensing

Input

Ref

Door

Switch

P12-9

13 V

P12-11

P10-2

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды