Whirlpool M-17 Скачать руководство пользователя страница 17

Страница: 17 / 88

GENERAL INFORMATION (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

1-13

Product Features

Whirlpool

Cycle Guide

CYCLE

Control

Purpose

Sensor

Senses soil to automatically optimize cycle. Auto cycle is selected if START is pressed first.

Heavy

Use for hard to clean items.

Normal

This cycle is recommended for daily, regular or typical use to completely wash and dry a full load of normally

soiled dishes.

Quick Wash

Use when you need faster results.

Soak & Clean

Use for loads with heavy amounts of dried on or hard to clean baked-on food. For best results add prewash

detergent.

OPTIONS

Control

Purpose

Hi Temp Wash

Helps remove tough, baked on food.

Sani Rinse

Sanitizes dishes and glassware in accordance with NSF International NSF/ANSI Standard 184 for Residential

Dishwashers. See this section in the Owner’s Manual.

Heat Dry

Dries dishes with heat. Load plastic item in upper racks.

Extended Dry

Increases the Energy used for drying the dishes. This may lengthen the cycle time.

Delay

Runs the dishwasher at a later time.

Start / Resume

Push to start or resume a cycle.

Cancel / Drain

Push to reset any cycle or options during selection. Push to end a cycle once started.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды