Whirlpool M-17 Скачать руководство пользователя

Страница: 57 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-19

Global Wash Motor VSM

This test will check the wiring to the wash motor and the wash

motor itself. The following items are part of the wash motor

circuit:

Harness/Connection

Wash Motor

Control Board

Test Procedure

Check the tube and sump for anything that may be impeding

water flow. Inspect and if necessary clean the coarse-filter

system. Also inspect spray arm and nozzle and clean if

needed.

Check the wash motor and electrical connections by

performing the Service Diagnostics Cycle. The following steps

assume that this step was unsuccessful.

Strip Circuit - Variable Speed Wash Motor

Unplug power or disconnect dishwasher.

Remove toe and outer door panels to access control board.

Unplug connector P5 from control board.

Check the wash motor using an ohmmeter, measure the

resistance between P5-1 and P5-2.

If the resistance is between 16-18 ohms, the wash motor

and harness are good. Go to step 7.

If outside the range, replace the wash motor.

If an open circuit is detected, check connections and

harness continuity between control and wash motor. If

good, replace the wash motor.

Reassemble all parts and panels.

Plug in dishwasher or reconnect power and run Diagnostics

Cycle to verify repair.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Variable

Speed

Controller

Variable Speed

Wash Motor

- 18

APPROX 60 W at 3200 RPM

Pin to Pin

Wash/Drain - On Some Models

P5-1

LT BU

Pin 3

Pin 2

Pin 1

LT BU

P5-2

P5-3

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды