Whirlpool M-17 Скачать руководство пользователя

Страница: 76 / 88

COMPONENT ACCESS (Cont.)

4-12

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Removing the Third Level Rack

(available on some models)

Open the dishwasher door.

To access track stops, pull the rack forward until it stops and

clicks into place.

To open track stops, flip the track stop to the outside of the

track.

After opening both track stops, slide front wheels up and out

of the slot in track. Continue to pull rack forward in track and

slide the back wheels up and out of the track.

Close track stops.

Slide rack tracks back into dishwasher.

Removing the Rack Rails

Turn white plastic rail retainers counterclockwise to remove

third level rack rails.

Use a 5/16" nut driver to remove the four bolts holding the

upper rack rail.

Remove Wash Tube Cover

Complete the steps 1-6 from

"Removing the Third Level

Rack"

section.

Pry two tabs outward and push to disengage Wash Tube

Cover from Manifold Drive Box.

Spread the two tabs to remove Manifold Drive Box from rails.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды