Whirlpool M-17 Скачать руководство пользователя страница 53

Страница: 53 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-15

Diverter Motor

This test will check the wiring to the diverter motor and the

diverter motor itself. The following items are part of the diverter

motor circuit:

Harness/Connection

Diverter Motor

Diverter Position Switch (see test on following page)

Control Board

Test Procedure

Check for operation in Diagnostics Cycle. Listen for water

spray changing zones or inspect shaft with mirror to see it

rotating during diverter interval. If diverter is rotating, the

likely problem is with the diverter sensor (see test procedure

on following page). Verify that diverter disk is properly

installed on shaft.

Are all the loads controlled by TRIAC not working?

YES - check for open door switch, TRIAC fuse, or pilot

relay.

NO - just the diverter valve. Go to step 3.

Strip Circuit - Diverter Motor

Unplug dishwasher or disconnect power.

Remove toe and access panels to access control board.

Unplug connector P6 from control board.

Check the diverter motor using an ohmmeter, measure the

resistance between P6-4 and P6-6.

If the resistance is between 1100-1400 ohms, the diverter

motor and harness are good. Go to step 7.

If outside the range, replace the diverter assembly.

If an open circuit is detected, check connections and

harness continuity between control and diverter

assembly. If good, replace the diverter assembly.

Reconnect P6 to control board.

Set voltmeter to AC and connect leads to test-pads

P6-4 and P6-6 on the control board. Plug in dishwasher or

reconnect power.

Start the Diagnostics Cycle and at the proper interval

measure for AC out of the control board between P6-4 and

P6-6 (Refer to Diverter Motor Strip Circuit below).

IMPORTANT:

The Diverter Motor must be connected to the

control board to measure voltage accurately.

If no AC voltage is measured, replace the control board

and retest.

If 120 VAC is measured and diverter is rotating, go to

step 10.

10.

Perform Diagnostics Cycle to verify repair.

If diverter error still exists, perform diverter sensor test

procedure on following page.

11.

Unplug dishwasher or disconnect power.

12.

Reassemble all parts and panels.

13.

Plug in dishwasher or reconnect power.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

BK P4-1

P6-6

P4-4

Pin 3

Pin 1

P5 Pins 1 and 4 to test fuse

N.O.

K503

Pilot L1 Relay

(Also see Door

Switch Circuit)

Fuse

F500

Electronic Control

Electronic

Control

Triac

Diverter Valve Motor

1,100 Ω - 1400 Ω

120 V, 60 Hz, 3 W

P6-4

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды