Whirlpool M-17 Скачать руководство пользователя страница 28

Страница: 28 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

2-8

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Service Error Codes (Continued)

FUNCTION CODE ERROR CODE

CAUSES

WHAT TO CHECK

8 - Inlet Water

5 - Fill valve

stuck open

Control detects water flowing through

flow meter when fill valve is turned off

Confirm dishwasher fills while door is open.

˗ If yes, unplug dishwasher or disconnect power,

turn off water to dishwasher, replace fill valve and

turn water back on.

˗ If filling stops with door open, but fault is detected

while running a cycle, unplug dishwasher or

disconnect power and replace control.

Fill valve TRIAC on control shorted

If dishwasher does not fill with door open, but F8E5

or F1E1 is detected while cycle is running, the fill

valve TRIAC is shorted. Disconnect power and replace

control.

6 - Flow meter

Disconnected or damaged flow meter

NOTE:

Control is programmed to

default to timed fill sequence if flow

meter malfunctions. Intermittent flow

meter connection may cause incorrect

fill levels or false fault codes to be

recorded.

1. Unplug dishwasher or disconnect power.

2. Check connections to flow meter with meter.

Verify that connector is securely connected at

the flow meter end and wires are not pinched/

damaged. Reconnect wires and/or replace

damaged components.

3. Inspect water inlet and flow meter for signs

of obstruction that prevent flow meter wheel

from turning. If wheel does not turn, or turns

intermittently, when water is flowing, replace

water inlet assembly.

9 - Draining

1 - Not draining

Obstructed drain hose or path

1. Unplug dishwasher or disconnect power.

2. Check for blockages from drain motor to

customer's plumbing. Check for plugged garbage

disposal or plug not knocked out, plugged hoses or

drain check valve stuck.

Drain pump impeller damaged

1. Unplug dishwasher or disconnect power.

2. Remove drain pump and check impeller (normally

there is some uneven resistance when pushing it).

If it is stripped or visibly damaged, replace drain

pump.

Drain motor electrical problem

Check other fault codes to see if F9E2 is also

recorded. See F9E2 description below.

Wash motor problem

1. Check other fault codes to see if F7E1 is also

recorded. Control uses wash motor signal to verify

drain so a failed wash motor can cause a drain

fault to be detected.

2. Check wash motor and filter assembly for proper

function.

2 - Drain motor

electrical

problem

Loose connection in drain motor

circuit and/or open drain motor

winding.

1. Unplug dishwasher or disconnect power.

2. Check resistances of drain motor winding and all

connections in the drain circuit. Fix/replace open

connection/part.

Debris stuck in drain motor impeller

causing locked rotor

1. Unplug dishwasher or disconnect power

2. Remove drain motor and dislodge debris from

impeller. Inspect for damage before reassembling.

Open fuse on control to drain motor

Refer to “Fuse Service and Resistance Check” in

section 3.

Drain motor drive circuit on control

1. Unplug dishwasher or disconnect power.

2. Check resistances of drain motor winding and all

connections in the drain circuit. If all connections

and drain motor winding measure good, replace

control.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды