Whirlpool M-17 Скачать руководство пользователя страница 34

Страница: 34 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

2-14

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Troubleshooting Guide (Continued)

CUSTOMER DESCRIPTION

POTENTIAL CAUSES

CHECK

RELATED

ERROR

CODES

Poor wash

Filters not cleaned or have been

reinstalled improperly.

1. Inspect filters and instruct customer

on how to remove, clean, and reinstall

them.

2. Ensure that filters are fully seated and

micro filter cup is tight in sump.

Little or no wash pump flow

Diverter problem. Refer to “

Service Error

Codes

” table.

F10E4 (FAE4)

1. Filter may be plugged with food soil

or hard water. Place mugs or glasses

upright in the middle and lower dish

racks.

2. Run a Normal cycle for 10-15 minutes.

Open the door and inspect mugs.

˗ If water is accumulating in them,

pump is working.

˗ If no water is present, water is not

being pumped through the spray

arms.

3. Inspect pump, filters, and spray arms.

If filter is plugged or damaged, unplug

dishwasher or disconnect power and

replace pump/ filter assembly. Clean or

replace clogged components. Ensure

that filters are fully seated in sump.

4. If hard water is present, instruct

customer on proper maintenance.

Spray arms not rotating or plugged

1. Check arm rotation. If arms are blocked

by dish item, instruct customer. Also

check for correct upper spray arm

alignment with docking station located

on feed tube at back tub wall.

2. Check nozzles. If they are plugged,

clean nozzles. Plugging may be caused

by hard water build up in water delivery

system, damage to pump filter, or

improper assembly of filters in sump.

Inspect water delivery system and

clean as needed. Inspect filters, clean,

reinstall, or replace.

Poor wash due to draining, dispensing

and/or temperature problems.

Refer to "Will not drain", "Detergent not

dispensing" or "Long cycles" sections

above. Refer to “

Service Error Codes

”

table.

F3E1

F9E1

F10E1 (FAE1)

Soil sensor is choosing low soil cycle

when high soil is present.

1. Check lens surface. Clean if needed.

If sensor cannot be cleaned or has

visible damage, unplug dishwasher or

disconnect power.

3. Replace OWI and run diagnostics

cycle after installing new OWI to force

calibration on next customer wash

cycle.

Diverter problem

Refer to “

Service Error Codes

” table.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды