Whirlpool M-17 Скачать руководство пользователя страница 30

Страница: 30 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

2-10

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Troubleshooting Guide

NOTES:

For resistance checks, refer to the “Component Testing” in Section 3.

For checking operation with diagnostics, refer to “

Service Diagnostics Cycle Timing

” section.

CUSTOMER DESCRIPTION

POTENTIAL CAUSES

CHECK

RELATED

ERROR

CODES

CLEAN LED Flashes

Control Programmed with Self

Diagnostics.

Read error code from the dishwasher and

refer to “

Service Error Codes

” table. Run

service diagnostics test cycle to read full

history of error codes.

F1E1

F7E1

F7E2

F8E1

F8E4

F8E5

F9E1

F10E5 (FAE5)

Won't run or power up

("Dead" keypad/console)

No operation

No keypad response

No LEDs or display

No power to unit or bad connection.

Check fuses, circuit breakers, and junction

box connections.

Loose connections in dishwasher power

up circuit or between keypad(s) and

control.

1. Unplug dishwasher or disconnect

power.

2. Check continuity power connections

keypad(s) and control.

User interface on this model is not

compatible with control which has been

exchanged with a control from another

model.

Unplug dishwasher or disconnect power.

Verify correct control is installed for this

model. Control is specific to each user

interface and model type. Call techline

to verify part numbers if necessary. If

incorrect control, replace.

Control detected door switch problem.

Refer to “

Service Error Codes

” table.

F5E1

User interface or control failure.

1. Unplug dishwasher or disconnect

power.

2. Replace user interface/console and/or

control.

Won't run and Start/Resume

LED is blinking slowly

By design, if door is opened for more

than 5 seconds or power is interrupted

during a cycle, the user must press Start/

Resume to resume operation.

Instruct customer. Refer to

Owner's

Manual

Start/Resume key not responding

See "One or more keys won't respond."

Control detected door switch problem.

Refer to “

Service Error Codes

” table.

F5E1

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды