Whirlpool M-17 Скачать руководство пользователя страница 43

Страница: 43 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-5

Control Board Information

Specifications

Electrical Supply

: (Under Load): 60 Hz 120 VAC

Supply Water Flow Rate

: To fill 2 qt (1.9 L) in 46 seconds, 120 psi

maximum, 20 psi minimum.

Supply Water Temperature

: 120°F (49°C) (Before starting a cycle,

run water from sink faucet until hot.)

Water Charge

: 1.0 gal. (3.9 L) Approximate

Lower Spray Arm Rotation

: 12 to 40 RPM

Upper Spray Arm Rotation

: 12 to 30 RPM

Fuse Service and Resistance Check

F500 = Small - TRIAC Load Fuse

Check operation of loads during the Service Diagnostics cycle.

If any of the TRIAC loads work, F500 Fuse is OK.

If all TRIAC loads fail to work, F500 Fuse could be open. See

Fuse Resistance Check.

Fuse Resistance Check:

Unplug the dishwasher or disconnect power.

Measure resistance of F500 Fuse.

NOTE

: Fuses are on the bottom of the Control Board but can be

checked from the top side. See "Control Pin-out" diagram.

If resistance is < 3 Ω, then fuse is OK.

If resistance is > 3 Ω, then fuse is OPEN.

If the fuse is open:

Inspect and check resistance of all loads on fuse. If any loads are

open, shorted, or have evidence of overheating or pinched wires,

replace them.

Component Testing

Testing Dishwasher Components from the Control

Before testing any of the components, perform the following

checks:

The most common cause for mis-diagnosed control failure

is poor connections. Therefore, disconnecting, inspecting,

and reconnecting wires will be necessary throughout test

procedures.

All tests/checks should be made with a VOM or DVM having a

sensitivity of 20,000 ohms-per-volt DC, or greater.

Check all connections before replacing components, look for

broken or loose wires, failed terminals, or wires not pressed

into connectors far enough.

Voltage checks must be made with all connectors attached to

the boards.

Resistance checks must be made with power cord unplugged

or power disconnected, and with wiring harness or

connectors disconnected from the control.

The testing procedures in this section may require the use

of needle probes to measure voltage. Failure to use needle

probes will damage the connectors.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды