Whirlpool M-17 Скачать руководство пользователя страница 46

Страница: 46 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

3-8

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

General Theory of Operation

Refer to Wiring Diagram on page

3-3

Neutral and L1 (AC voltage) enters the Control Board at P4,

pins 4 and 1 respectively. AC is converted to DC voltage at the

Low Volts Power Supply (LVPS). Supplies include 13 VDC and

5 VDC, and DC GND (REF). These low voltage supplies are used to

provide power to the microprocessors and board components,

control the TRIAC, power the sensors, user interface, buzzer, fan

motor, and energize the AC relays.
The 13 VDC is vital to the operation of the dishwasher.

This supply is necessary to operate all 120 VAC loads in the

dishwasher, whether they are connected to a relay or controlled

by TRIAC. 13 VDC is generated by the power supply and flows

through the door switch-when closed-to be available to the

heater relays (L1 and N), wash motor relay, and the pilot relay.

A relay coil becomes energized when the control closes

the LV drive circuit for a specific relay completing 13 V pathway,

which in turn closes the relay switch providing AC to the load.

The Pilot relay provides "L1" to the remainder of the components

that are controlled by the Neutral-sensed TRIAC.
In the micro-filtration dishwasher, there are 2 or 3 fuses on the

Control Board: F500 Small TRIAC Load Fuse, F101 Main Power

Supply Fuse, and F501 Wash Motor Fuse. If the TRIAC Fuse is

open, all loads controlled by TRIAC will not operate. If the Main

Power Supply Fuse is open, no 5 V or 13 V supply will be available

and the unit will appear to not power up. If the Wash Motor Fuse

(optional) is open, all loads will work except the wash motor.

NOTE:

Refer to "Fuse Service and Diagnostic Checks" on page

3-4

Power Check

This test checks for incoming and outgoing power to and from

the control board. This test assumes that proper voltages is

present at the outlet or direct connect cable.

Test Procedure

Unplug dishwasher or disconnect power.

Remove access panel.

Remove terminal box cover.

With a voltmeter set to AC, place black probe on white

terminal block screw head (N) and red probe on black

terminal block screw head (L1).

Plug in dishwasher or reconnect power.

If 120 VAC is present, unplug dishwasher or disconnect

power and proceed to step 6.

If 120 VAC is not present, have customer correct power.

Remove the outer door panel to access the control board.

Remove cover from control board and locate connector P4.

With a voltmeter set to AC, connect black probe to P4,

pin 4 (N) and red probe to P4, pin 1 (L1).

Plug in dishwasher or reconnect power.

If 120 VAC is present, go to step 10.

If 120 VAC is not present, check for open connection

between terminal block and control. Repair as needed.

10.

Verify DC Supplies.

•

5 VDC is used to power IC's and micro-processors on the

circuit board as well as provide power to the sensors.

If 5 VDC were missing, the OWI (Optical Water Indicator)

and user interface would not function. To verify 5 V ± 5%,

with a voltmeter set to DC, connect the black lead to

P10-2 (DC GND) and the red lead to P11A-2 or P11B-2

(5 V).

•

13 VDC is used to actuate the 120 VAC relays and TRIAC on

the control, the overfill switch input, and the LEDs on models

with interior lighting.

If 13 VDC was missing, the heater, motors, and all the

other loads would not turn on as well as the LEDs on

models with interior lighting. The control would falsely

detect an overfill fault. To verify 13 V ± 5%, with a

voltmeter set to DC, connect the black lead to P10-2

(DC GND) and the red lead to P11-7 (13 V).

Troubleshooting Missing DC Supplies:

Refer to the Wiring

Diagram on page

3-3

when troubleshooting the DC supplies. If

5 VDC or 13 VDC is missing on the control, unplug dishwasher

or disconnect power, and then disconnect all components/

loads from the control relying on the missing or loaded

supply. Plug in dishwasher or reconnect power and check if

the DC supply has returned.

If not, replace the control.

If it has, turn off dishwasher and reconnect one connector

at a time until the component loading down that supply

has been identified.

11.

Unplug dishwasher or disconnect power.

12.

Reassemble all parts and panels.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды