Whirlpool M-17 Скачать руководство пользователя страница 19

Страница: 19 / 88

GENERAL INFORMATION (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

1-15

Product Features (Continued)

Maytag

Cycle Guide

CYCLE

Control

Purpose

Auto

Senses soil to automatically optimize cycle. Auto cycle is selected if START is pressed first.

PowerBlast

Use for hard to clean items.

Normal

This cycle is recommended for daily, regular or typical use to completely wash and dry a full load of normally

soiled dishes.

Quick

Use when you need faster results.

Rinse

Use for rinsing dishes, glasses, and silverware that will not be washed right away. Do not use detergent.

OPTIONS

Control

Purpose

High Temp

Helps remove tough, baked on food.

Sani Rinse

Sanitizes dishes and glassware in accordance with NSF International NSF/ANSI Standard 184 for Residential

Dishwashers. See this section in the Owner’s Manual.

Heated Dry Short

(Some Models)

Power Dry Short

Dries dishes with heat. Load plastic item in upper racks.
Dries dishes with heat and a fan. Load plastic item in upper racks.

Heated Dry Long

(Some Models)

Power Dry Long

Increases the Energy used for drying the dishes. This may lengthen the cycle time.

Delay

Runs the dishwasher at a later time.

Start / Resume

Push to start or resume a cycle.

Cancel / Drain

Push to reset any cycle or options during selection. Push to end a cycle once started.

Control Lock

(on some models)

Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option

changes during a cycle. To turn ON/OFF, hold button for 3 seconds.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды