Whirlpool M-17 Скачать руководство пользователя страница 24

Страница: 24 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

2-4

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Service Error Codes

Fault codes are intended to give direction as to which

component or subsystem has a failure. Service technician should

troubleshoot the issue and confirm the validity of all fault codes

before replacing parts.

FUNCTION CODE ERROR CODE

CAUSES

WHAT TO CHECK

1 - Control

1 - ACU

Relay or TRIAC failure on main control

board.

Unplug dishwasher or disconnect power and replace

control.

2 - MCU

Motor control circuit failure on main

control board.

Unplug dishwasher or disconnect power and replace

control.

2 - User Interface 1 - Stuck Key

Control detected stuck keys in user

interface.

NOTES:

˗ If any keys are stuck, the stuck

key(s) will be ignored and an error

recorded to service history, but no

alert to customer.

This fault is monitored on models

with key switches only, not on

capacitive touch key models.

Check responsiveness of each key. If some keys do

not respond, replace user interface. If all keys are

responsive, fault may be intermittent or caused by

customer use. Check for vent and/or fan fault, which

may lead to excessive moisture build up in door cavity

and cause keys to appear stuck closed.

3 - Thermistor/

OWI

1 - Open or

Shorted

˗ Open or shorted connection or

component in temperature sensing

circuit

˗ Open, shorted or faulty temperature

sensor

Temperature sensor input on

control failed

˗ Incoming water temperature above

167oF (75oC)

1. Unplug dishwasher or disconnect power.

2. Check all components and connections in the

temperature sensing circuit with meter.

Fix/replace open/shorted connection or part.

3. Verify incoming water temperature.

2 - Failed

Calibration

˗ OWI failure

˗ OWI lens obstructed by hard water

build up or food soil

1. Check OWI lens surface. Clean if needed.

2. Unplug dishwasher or disconnect power.

3. Check all connections in soil sensing circuit with

meter. Fix/replace bad connection/part.

NOTE:

Run diagnostics cycle after installing new

OWI to force calibration on next regular wash cycle.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды