Whirlpool M-17 Скачать руководство пользователя страница 23

Страница: 23 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-3

Service Diagnostics Cycle Timing

Numeric Display

All LEDs on

5 (Some

models)

Interval Time

0:01

0:02

Typical: 0:30

Max: 5:00

0:01

Typical: 1:00

Max: 2:09

0:18

Typical: 0:15

Max: 0:24

Typical: 0:20

Max: 0:44

0:01

0:20

0:30

0:15

Typical:

30 Max: 4:45

0:15

0:01

Service Test Steps

Pause

Turn on vent

(Stay on

throughout)

Timed or

Sensed Drain

Pause

Fill 2.5 L

Wash motor

pulses

Fill 0.5 L

Fill 0.8 L +

Wash

Pause

Wash =

Dispenser

(Middle spray

arm)

Wash = Fan

(Ceiling spray

arm)

Wash (Third

Level Rack

)

Wash +

Heater (Lower

spray arm)

Wash + Drain Sensed Drain

Drain

Pause

Typical Total Time

4:59

NOTES:
1.

Time varies depending on drain sensing.

Time varies depending on fill rate sensed by flow meter.

This interval is only included on models with a wash arm in the third level rack.

Cycle times out after 5 minutes.

Activating Service Diagnostics Mode

To invoke the Service Diagnostics Mode, perform the following while in standby:

Press any 3 keys (except Delay, Start or Cancel) in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than 1 second between key

presses. All LED's will illuminate if successful. Then press button #2 and shut door to start the service cycle.

The Service Diagnostics Cycle will start when the door is closed.

Invoking Service Diagnostics clears all status and last run information from memory and restores defaults. It also forces the next

cycle to be a sensor calibration cycle.

Sensor calibration cycle may add an extra rinse (to assure clear water) before the final rinse. This cycle may be longer than a

typical run.

All LEDs turn on immediately upon receiving entry sequence (even if door is open) as a display test. A tone may play depending

on the model.

Press Key #1: User Interface Test

All LEDs remain on. Tone is played for each key pressed.

Press Key #2: Run Service Test Cycle

To rapid advance 1 step at a time, press the Start/Resume key. Rapid advance may skip some sensor checks and prevent fault

detection from working properly. Rapid advance can also cause false error codes to be detected in some cases.

NOTE:

The diagnostics cycle will pause when the door is opened and resume when closed. No Start/Resume key press required to

resume.

Press Key #3: Error Code History Display

Up to 5 unique codes are saved in the history.

Most recently detected error code is displayed first.

If no faults are present, numeric display will show "-:--" or Clean LED will be off (Depending on display type).

Press third key to advance to next error code stored. Three tones are played when the end of the error code history has been

reached.

Press and Hold Key #3: Clear Fault History

Tone will play when faults are cleared Exit procedure.

The service diagnostics mode will timeout after 5 minutes of user inactivity.

Press Cancel key to exit service diagnostics mode.

Service diagnostics mode will be canceled if AC power is removed from the appliance.

Service Diagnostics Mode Menu Table

Types of Button Press

1st Button

2nd Button

3rd Button

Momentary Press

Activates User Interface Test

Activates Service Test Cycle

Displays Next Error Code

Hold for 5 seconds

Clears Error Code History

Service Diagnostics Cycle Notes

Drain may be sensed or timed. Sensed drain maximum time is approximately 5 minutes, which includes retries. Sensed drain will

have both wash motor and drain motor powered simultaneously. Timed drain is drain motor only.

Fills are measured by flow meter and time may vary according to water flow rate. If flow meter has failed, control will revert to timed

fills and record fault code to history. Wash motor may turn on during fill process to verify the presence of water in the machine.

This step is only included on models that have a wash zone in the third level rack. On models without a third level wash zone or two

racks, this step is skipped.

Reading Fault Code Display

Point LED Models

Each fault code is displayed by blinking the Clean or Complete LED in a pattern to indicate the Function code and the Error code.

Fault display is a 4 step process. Count LED blinks for each portion of the code.

1.  Blink Clean or Complete LED Function code number of times
2.  Pause 2 seconds
3.  Blink Clean or Complete LED Error code number of times
4.

Pause 5 seconds

Each fault code is repeated until key #3 is pressed to advance to the next code or until the service mode is exited.

Numeric Display Models

Each fault code is shown in the numeric display by first showing the Function code "F#" then the Error code "E#".

Fault display is a 4 step process:

1.  Display F#
2.  Pause 0.5 seconds
3.  Display E#
4.

Pause 1 second

Each fault code is repeated until key #3 is pressed to advance to the next code or until the service mode is exited.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды