Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 145

Gates

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

145

5.13 Gates

In this function group you will find all functions for setting
the gates.

Tasks of the gates

The gates monitor the area of the test object where you
expect to detect a flaw. If an echo exceeds or falls below
the gate, an alarm signal can be output (see page 143).
Gates are displayed in different colors for ease of iden-
tification (see page 80).

The gates A and B are independent of each other.
Gate A can also assume the function of an echo start
gate for gate B (see page 151).

The gates are also used to choose the echo for the dig-
ital time-of-flight and amplitude measurement. The
measured value is displayed in the measurement line
(see page 85).

Gate Selection

With this function you first select the gate for which the
following settings are to apply. You can set the settings
for each gate independently.

«
...
143
144
145
146
147
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов