manualshive.com logo in svg

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 259 / 330

Поделиться
Скачать
Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 259

Battery care

7  Maintenance and care

Krautkrämer USM 100

Rev. 9 (09/2023)

259

7.3 Battery care

Transport and storage

ATTENTION

Lithium batteries, identified as being defec-
tive for safety reasons, or that have been 
damaged, that have the potential of produc-
ing a dangerous evolution of heat, fire or 
short circuit are forbidden for transport by air.

Pay attention to the permissible ambient conditions for 
transport and storage (see 

Specifications

 from 

page 303).

To prevent short circuits and the associated heating, 
lithium batteries must never be stored or transported un-
protected. Suitable measures against short circuits are 

●

inserting the batteries in original packaging, in the 
system case of the instrument or in a plastic bag, 

●

taping the battery terminals.

Before transporting by air, 

●

make sure that the battery charge is below 30%,

●

pay attention to the information on transport and stor-
age in the technical documentation of the specific 
battery, 

●

follow the instructions of the shipping company for 
packing and transport of lithium batteries.

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов