Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 65

Страница: 65 / 330

Remote Connection Setup

3 Initial start-up

Krautkrämer USM 100

Rev. 9 (09/2023)

Establishing the remote connection

– Check that the USB-C hub is correctly connected to

the USM 100.

– Check that the computer and the USM 100 are con-

nected to the same network.

– Check that the remote control is enabled in the

USM 100 (see page 64).

– Launch the VNC client, for example the

RealVNC

viewer

– Enter the IP address of the USM 100 in the address

field and press the Enter key.

The connection is established and after a short time you
will see the screen of the USM 100 on the monitor of the
computer.

If an encryption warning message is shown on the
screen, click the

Continue

button.

If there is a problem with the connection, check the web-
site of the VNC client you are using for possible causes
and suggested solutions.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 65 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: