Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 56

3 Initial start-up

Starting the USM 100

56

Rev. 9 (09/2023)

Krautkrämer USM 100

3.6 Starting the USM 100

Powering On

The Power key (1) is located on the top of the instru-
ment.

– Press the Power key for two seconds.

The software is initialized, the instrument carries out a
self-check and then switches over to stand-by mode.

In the factory setting, after switching on the instrument
and system boot-up, you will see the

Application desk-

(see page 69) with all applications stored in the in-

strument and available for selection.

Depending on the settings (see

Startup Application

A-scan view

(see page 73) can be dis-

played alternatively. In this case, the application select-
ed as the default is already loaded.

In case the instrument can not be started in the normal
way, you can reset or reinitialize the operating system
with a software update (see page 265).

1

«
...
54
55
56
57
58
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов