Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 142

5 Operation

UT Setup

142

Rev. 9 (09/2023)

Krautkrämer USM 100

When the automatic gain control is switched on, further
functions are displayed with which you can configure
the AGC (see below).

AGC Max Amp / AGC Min Amp

To configure the automatic gain control, enter the mini-
mum and the maximum height of amplitude in percent
screen height that the echo signal should reach within
the gate.

Note

The smaller the ratio between the values

AGC Max Amp

and

AGC Min Amp

, the

more sensitive the control process.

AGC Noise

You can define a threshold for the noise. Signals below
this threshold are not taken into account for the auto-
matic gain control.

LED Alarm

You can use the multi-color LED next to the screen (see
page 102) as an alarm signal. If the alarm event occurs,
the LED lights up accordingly.

The gate for triggering the alarm is selected in the func-
tion

Alarm Select

.

Tone Alarm

You can output alarms as an acoustic signal directly
with the device. If an alarm event occurs, the signal
sounds.

The gate for triggering the alarm is selected in the func-
tion

Alarm Select

.

«
...
140
141
142
143
144
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов