Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 187

Страница: 187 / 330

DGS

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

187

Turning the DGS evaluation off

You can turn the DGS evaluation off at any time.

– Set the function

DGS Mode

Off

in order to hide the

curve.

Note

The recorded reference echo is not lost by
turning the function off. By turning it on again,
you can use the function

DGS Mode

to go

back to the DGS evaluation again without
losing any settings.

Deleting a DGS reference echo

You can delete the echo of the reference reflector. After
this, the DGS evaluation is not possible until you have
recorded a new reference echo.

– Tap the

Clear

icon in the Command bar (see

page 75). A confirmation message is shown.

– Confirm the deletion.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 187 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: