Volkswagen CC 2012 Скачать руководство пользователя | Manualshive

Страница: 170 / 222

background image

13 - Union

❑ To loosen and tighten union nut, counterhold with a wrench on connection.
❑ Before installing high-pressure pipe, first tighten connection to 40 Nm.

14 - Fuel distributor

❑ the lower part of the intake manifold must be removed to remove the fuel rail
❑ For cylinders 1, 3 and 5
❑ If the fuel rail is removed, the injector O-ring, support washer, spring element and combustion chamber

seal must always be renewed

❑ Tighten evenly from inside to outside.

15 - Union

❑ To loosen and tighten union nut, counterhold with a wrench on connection.
❑ Before installing high-pressure pipe, first tighten connection to 40 Nm.

16 - Connecting pipe

❑ 28 Nm
❑ Make sure that fuel pipe does not touch other components!
❑ Install free of tension.
❑ To install, first tighten union nuts hand tight.
❑ To loosen and tighten the union nut, counterhold with a wrench at high-pressure pump connection.
❑ Before installing: first tighten connection at high-pressure pump to 40 Nm.

17 - Union

❑ To loosen and tighten union nut, counterhold with a wrench on connection.
❑ Before installing high-pressure pipe, first tighten connection to 40 Nm.

18 - Fuel distributor

❑ For cylinders 2, 4 and 6
❑ If the fuel rail is removed, the injector O-ring, support washer, spring element and combustion chamber

seal must always be renewed

❑ Tighten evenly from inside to outside.
❑ Removing and installing

19 - Fuel pressure sender - G247-

❑ Before installing, coat front sealing taper and threads with clean engine oil.
❑ 22 Nm

20 - 22 Nm
21 - Pressure limiting valve

❑ Before installing lightly moisten O-rings with clean engine oil.
❑ Renew removed valve.
❑ Press in by hand using an 8 mm hexagon key.

22 - Bolt

❑ 30 Nm + 90° (

1

/4 turn) further

❑ Renew
❑ Tighten fuel rails evenly from inside to outside.

23 - Injector, cylinder 2 - N31-

❑ Injector, cylinder 4 - N33-
❑ Injector, cylinder 6 - N84-
❑ Removing and installing

24 - Support washer

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

164

Rep. gr.24 - Mixture preparation - injection

«
...
168
169
170
171
172
...
»

Содержание CC 2012































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC 2012

Бренд: Jeep Страницы: 212

Retrotech RTX-68D-CHG

Бренд: Dakota Digital Страницы: 4

Бренд: Porsche Страницы: 192

Бренд: Kuda-Phonebase Страницы: 3

Бренд: PEUGEOT Страницы: 128

Бренд: Schumacher Electric Страницы: 87

2009 ESCALADE ESV

Бренд: Cadillac Страницы: 602

Бренд: Subaru Страницы: 34

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

MagicComfort MSH200

Бренд: Waeco Страницы: 108

Бренд: Tusk Страницы: 2

Бренд: Cadillac Страницы: 522

Бренд: PEUGEOT Страницы: 17

Бренд: Mercedes-Benz Страницы: 91

OPTIA hybrid 2020

Бренд: Kia Страницы: 54

Бренд: Prorack Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды