Volkswagen CC 2012 Скачать руководство пользователя

Страница: 23 / 222

– Remove starter -A- ⇒ Electrical system; Rep. gr. 27 ; Starter;

Removing and installing starter .

It is advisable to remove the »lower« bolt first.
– Release rotary locking mechanism of connector -1- for me‐

chatronic unit by turning in »anti-clockwise direction« and pull

off connector.

– Undo all upper engine/gearbox connecting bolts. The insert

tool 18 mm - T10179- can be used for this.

Note

Figure shows the engine and gearbox installed.

One bolt is located in the starter motor hole -arrow-. This bolt can

be removed using multi-point bit - T10061- .
– Before unscrewing the last securing bolts, support gearbox

using workshop hoist .

– Remove lower engine/gearbox securing bolts.
– Press gearbox off from engine, guiding the gearbox
– Remove remaining engine/gearbox connecting bolts.
Connecting
Reassembly is carried out in the reverse order; note specified

torques:
♦ Specified torques ⇒ Rep. gr. 34 ; Removing and installing

gearbox; Specified torques for gearbox .

1.3

Securing engine on engine and gearbox

support

Note

The engine can be fastened to the engine and gearbox support -

VAS 6095- engine and gearbox support or the engine bracket -

3269- according to choice. We recommend using the engine

bracket - 3269- for work on the chain drive.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Removing and installing engine

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды