Volkswagen CC 2012 Скачать руководство пользователя

Страница: 10 / 222

Safety information

⇒ “3.1 Safety precautions during work on fuel system”,

page 4
⇒ “3.2 Safety precautions when using testers and measuring in‐

struments during a road test”, page 4
⇒ “3.3 Safety precautions when working on the cooling system”,

page 5
⇒ “3.4 Safety precautions when working on ignition system”, page

3.1

Safety precautions during work on fuel

system

WARNING

The fuel line is under pressure.
Fuel poses danger of injury to eyes and skin.
Wear protective goggles and protective clothing to avoid injury

and contact with the skin. Wrap a cloth around the connection

before loosening hose connections. Then reduce pressure by

carefully opening the connection.
For reasons of safety, the power supply to the fuel pump must

be interrupted before the fuel system is opened. The fuel pump

would otherwise be activated when the driver's door is opened

or the ignition is switched on. Use one of the following options

to interrupt the power supply:

♦ Disconnect battery

♦ Remove fuse for fuel pump - G6-

♦ Pull connector off fuel delivery unit flange

Caution

Observe the following during all assembly work, particularly in

the engine compartment due to the restricted space:

♦ Route lines of any kind and cables so that original routing

is restored.

♦ Ensure that there is sufficient clearance to all moving or

hot components.

3.2

Safety precautions when using testers

and measuring instruments during a

road test

Note the following if testers and measuring instruments have to

be used during a road test:
♦ Testers and measuring instruments must always be secured

to rear seat and operated by a second person from this loca‐

tion.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

Rep. gr.00 - Technical data

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды