Volkswagen CC 2012 страница 15 Скачать руководство пользователя

Страница: 15 / 222

Note

♦

Read the event memories of all control units ⇒ Vehicle diag‐

nostic tester.

♦

All cable ties that are opened or cut through when the engine

is removed must be renewed/replaced in the same position

when the engine is installed.

♦

Leave the ignition key in the ignition lock to prevent the steer‐

ing lock engaging.

♦

Seal disconnected fuel and breather lines so that the system

is not contaminated with dirt.

♦

Some components cannot be removed, or removed only with

difficulty, with the engine installed. Therefore, you should de‐

termine all defective components before removing engine and

renew them while engine is removed.

♦

To prevent damage to removed components, place them in

the container for removed parts - V.A.G 1698- .

Caution

Observe the following during all assembly work, particularly in

the engine compartment due to the restricted space:

♦ Route lines of any kind and cables so that original routing

is restored.

♦ Ensure that there is sufficient clearance to all moving or

hot components.

Disconnect earth strap at battery with ignition switched off ⇒

Electrical system; Rep. gr. 27 ; Battery; Disconnecting and con‐

necting battery .
– Completely remove air filter housing with connecting hose to

the throttle valve module - J338-

⇒ page 174

– Remove the bracket for the air-filter housing

⇒ Item 17 (page 174)

– Remove wiper arms and plenum chamber cover ⇒ General

body repairs, exterior; Rep. gr. 50 ; Bulkhead; Removing and

installing plenum chamber cover .

Vehicles with anti-theft secured engine control unit:
– Remove the U-shaped striker from the engine control unit

⇒ page 190

Continued for all vehicles:
– Pull engine wiring harness connector off at engine control unit.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Removing and installing engine

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды