Volkswagen CC 2012 Скачать руководство пользователя

Страница: 32 / 222

– Renew assembly mounting bolts -arrows- in succession (if not

already carried out on installing engine) and screw in hand-

tight.

Align engine bracket: There must be a distance -a- of at least

10 mm between engine support and right longitudinal member.
The cast edge on the engine support -2- must be aligned parallel

to the support arm -1- (distance -x- must be identical at front and

rear).
– Tighten bolts for engine mounting. Specified torques

⇒ page 21

Adjusting gearbox mountings:
– Renew gearbox mounting bolts -arrows- in succession (if not

already carried out when installing the engine) and screw in

hand-tight.

– On gearbox side, ensure that edges of support arm -1- and

gearbox mounting -2- are parallel.

• Dimension -x- must be identical on both sides of mounting.
– Tighten bolts for gearbox mounting. Specified torques

⇒ page 21

Further installation is carried out in the reverse sequence.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

Rep. gr.10 - Removing and installing engine

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды