Volkswagen CC 2012 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 222

Volkswagen CC 2012 Скачать руководство пользователя страница 108

Not illustrated:

♦ Sealant - D 176 501 A1-
Removing:
– Remove air filter housing

– Remove upper part of intake manifold

– Remove cylinder head cover

.

– Removing the two camshaft adjusters

– Undo bolts -arrows- from valve timing housing and pull valve

timing housing off cylinder head.

– Lay camshaft timing chain aside.

A - Inlet camshaft
– First remove bearing caps 1 and 13.
– Remove bearing caps 3 and 11.
– Remove bearing cap 7.
– Loosen bearing caps 5 and 9 alternately and diagonally.

B - Exhaust camshaft
– First remove bearing caps 2 and 14.
– Remove bearing caps 4 and 12.
– Remove bearing cap 8.
– Loosen bearing caps 6 and 10 alternately and diagonally.
Continuation for both camshafts
– Carefully remove camshafts and lay aside on clean surface.
– Remove roller rocker fingers together with supporting ele‐

ments and place them on a clean surface.

– Ensure that roller rocker fingers and supporting elements are

not interchanged.

Installing:
Conditions:

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

102

Rep. gr.15 - Cylinder head, valve gear

«
...
106
107
108
109
110
...
»

Содержание CC 2012































































































































































































































Отзывы:

Нет отзывов