Volkswagen CC 2012 Скачать руководство пользователя

Страница: 37 / 222

16 - Deflection rollers

❑ 40 Nm

1.3

Removing and installing poly-V belt

Special tools and workshop equipment required
♦ Pin - T10027-

Removing poly V-belt:
– Remove noise insulation ⇒ General body repairs, exterior;

Rep. gr. 66 ; Noise insulation; Assembly overview - noise in‐

sulation .

– Remove front right wheel housing liner ⇒ General body re‐

pairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing

and installing front wheel housing liner .

Caution

Danger of destruction due to reverse running direction in the

case of a poly V-belt that has already run.

♦ Before removing the poly V-belt, use a piece of chalk or a

felt pen to mark the running direction.

– Position spanner -1- onto tensioning roller securing bolt and

turn in -direction of arrow- until locking pin - T10027- can be

inserted on tensioning roller.

– Remove poly V-belt.
Installing poly V-belt:

Note

♦

Before installing the poly V-belt, ensure that all units (alterna‐

tor, air conditioner compressor) are securely bolted on.

♦

Check deflection rollers for ease of movement.

♦

The poly V-belt must not be kinked.

♦

When fitting poly V-belt, check direction of belt rotation and

make sure the belt is properly seated in the belt pulleys.

– Fit poly V-belt as illustrated.
– Use spanner -1- to push tension roller slightly in direction of

-arrow- in order to engage locking pin - T10027- in tensioning

roller.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Cylinder block (pulley end)

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды