manualshive.com logo in svg

Volkswagen CC 2012, Руководство по ремонту


Поделиться
Скачать
background image

– Unscrew securing bolts for lower part of intake manifold/cyl‐

inder head -arrows-.

– Unscrew securing bolt from oil dipstick guide tube -1-.
– Remove bracket -2- from lower part of intake manifold.
– Unscrew bolt -3-.
– Undo bolts of fuel rail for cylinders 2, 4, and 6 -arrows-.
– Carefully pull fuel rail off injectors.
– Remove lower part of intake manifold.

Note

Block off intake ports in cylinder head with a clean cloth.

Installing:
Install in reverse order of removal, observing the following.
– Before installing fuel rail, always renew injector O-ring, support

washer, spring element and combustion chamber seal

⇒ page 170

 .

– Lightly moisten O-rings between injector and fuel rail with

clean engine oil.

– Fit lower part of intake manifold with a new gasket.
– Set fuel rail and evenly press onto injectors.

Caution

The injectors must not be pulled into their seat with the fuel rail

bolts. Otherwise the spring element will be damaged.

– Fit all intake manifold and fuel rail securing bolts by hand.

Note

♦

Tighten fuel rail securing bolts on cylinder head evenly from

inside to outside.

♦

Then tighten securing bolts for lower part of intake manifold/

cylinder head.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

180

     Rep. gr.24 - Mixture preparation - injection

Содержание CC 2012































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC 2012

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
AAMP of America iSimple Operation Manual preview
iSimple
Бренд: AAMP of America Страницы: 6
NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Бренд: NavLinkz Страницы: 4
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
Dodge 8W-30 Wiring Diagram preview
8W-30
Бренд: Dodge Страницы: 24
Road Ranger H392 Installation Manual preview
H392
Бренд: Road Ranger Страницы: 22
Yakima LowRider Manual preview
LowRider
Бренд: Yakima Страницы: 15
Gator GRM430EM User Manual preview
GRM430EM
Бренд: Gator Страницы: 6
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Бренд: ECS Страницы: 4
Whispbar WB751 Manual preview
WB751
Бренд: Whispbar Страницы: 15
Kia OPTIA hybrid 2020 Features & Functions Manual preview
OPTIA hybrid 2020
Бренд: Kia Страницы: 54
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
Aston Martin V8 Vantage Workshop Manual preview
V8 Vantage
Бренд: Aston Martin Страницы: 415
Connects2 PARK-401 User Manual preview
PARK-401
Бренд: Connects2 Страницы: 2
Ultraplast MD19 User Manual preview
MD19
Бренд: Ultraplast Страницы: 5
Curt Manufacturing LIPPERT 18109 Installation Manual preview
LIPPERT 18109
Бренд: Curt Manufacturing Страницы: 3
Directed 403.NISS4HT 2.36 RSR Installation Manual preview
403.NISS4HT 2.36 RSR
Бренд: Directed Страницы: 22
Ratio Electric HOME BOX SMART Manual preview
HOME BOX SMART
Бренд: Ratio Electric Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды