Volkswagen CC 2012 Скачать руководство пользователя

Страница: 128 / 222

17 – Lubrication

Sump, oil pump

⇒ “1.1 Assembly overview - sump/oil pump”, page 122
⇒ “1.2 Removing and installing oil spray jet”, page 124
⇒ “1.3 Removing and installing sump”, page 125
⇒ “1.4 Removing and installing oil pump”, page 127
⇒ “1.5 Engine oil:”, page 131

1.1

Assembly overview - sump/oil pump

Note

♦

If large quantities of metal chips and abraded material are

found during engine repair, this may indicate that the crank‐

shaft bearings or conrod bearings are damaged. To avoid any

subsequent damage, the following work must be carried out

following the repair:

♦

Thoroughly clean oil channels.

♦

Renew oil spray jets.

♦

Renew engine oil cooler.

♦

Renewing oil filter.

♦

The oil level must not be above the max. marking on the dip‐

stick - danger of damage to the catalytic converter! Markings

⇒ page 131

, Checking engine oil level.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

122

Rep. gr.17 - Lubrication

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды