Volkswagen CC 2012 Скачать руководство пользователя страница 115

Страница: 115 / 222

– Remove tensioner for timing chain -arrow-.

– Mark chain links that are opposite the markings on the cam‐

shaft adjusters. Installation is facilitated by marking the timing

chain.

– Undo and remove camshaft adjuster bolts and remove cam‐

shaft adjuster.

Note

The timing chain must be held by its bottom cover in order to hold

it in position on the sprocket of the oil pump. The timing chain

cannot jump over.

Installing camshaft adjuster
Condition:
• Crankshaft is at »TDC« position
• Chain drive sprocket for high-pressure pump is fixed in place

with adjusting tool - T10363-

• Camshafts have been fixed in place with camshaft bar -

T10068 A-

First install camshaft adjuster for inlet camshaft as follows:

Note

Due to a fitted key, camshaft adjusters can only be bolted on in

one position -arrows- at camshaft mounting.

– Put on inlet camshaft adjuster with fitted timing chain onto

camshaft. Observe the following:

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

4. Valve gear

109

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды