Volkswagen CC 2012 Скачать руководство пользователя страница 83

Страница: 83 / 222

– Remove old sealing compound from holes -arrow- of cylinder

head gasket.

Note

With the cylinder head installed, the holes in the cylinder head

gasket are only half visible.

Caution

Avoid damage to cylinder head gasket. If the cylinder head

gasket is bent excessively, it can be kinked. A kinked cylinder

head gasket must be renewed.

– Bend end of cylinder head gasket down very slightly

-arrows-, just far enough to be able to clean upper sealing

surface on cylinder head gasket and cylinder head.

– Clean top and bottom of cylinder head gasket; both faces must

be free of oil and grease.

– Cut off nozzle on tube at front marking (∅ of nozzle approx.

2 mm).

– Apply thin coating of sealant to upper and lower sealing sur‐

faces of cylinder head gaskets; to do this, bend cylinder head

gasket downwards very slightly -arrows-.

– To coat the surface between cylinder head and gasket use a

flat object, e.g. a feeler gauge.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

2. Cover for timing chain

Содержание CC 2012































































































































































































































Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды

Volkswagen CC 2012, Руководство по ремонту

Результаты поиска

Содержание CC 2012

Отзывы:

Похожие инструкции для CC 2012

Бренды по названию

Популярные бренды