Valleylab Force EZ - C Series Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 208

background image

Fuses

Replacement Procedures

Force EZ-C Series Service Manual

8-15

Install a new fuse on the low voltage power supply.

1.

Replace the blown fuse with a fuse of the same type and rating (F2A).

2.

Install the Control board.

a.

Position the Control board over the Power Supply/RF board, fitting the
edge of the Control board into the slot on the right heat sink.

b.

Slide the board down, carefully fitting the edge connector into the
matching connector on the Power Supply/RF board.

c.

Place the retention bracket on the left rear heat sink and install the screw
that secures the bracket to the heat sink.

d.

Connect the Display board ribbon cable to the Control board and lock the
connector.

3.

Position the cover above the chassis and slide it down. Tighten the four screws
that secure the cover to the chassis.

Replacing the Fuse on the Power Supply/RF Board

Equipment

•

Phillips screwdriver

•

Fuse puller

Warning

Fire Hazard

– For continued protection against fire hazard, replace fuses only

with fuses of the same type and rating as the original fuse.

Warning

Electric Shock Hazard

.– To allow stored energy to dissipate after disconnecting

power, wait at least five minutes before replacing parts.

Fire Hazard

.– For continued protection against fire hazard, replace fuses only

with fuses of the same type and rating as the original fuse.

Caution

The generator contains electrostatic-sensitive components. When repairing the
generator, work at a static-control workstation. Wear a grounding strap when
handling electrostatic-sensitive components,

except

when working on an

energized generator. Handle circuit boards by their nonconductive edges. Use an
antistatic container for transport of electrostatic-sensitive components and circuit
boards.

«
...
169
170
171
172
173
...
»

Содержание Force EZ - C Series

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force EZ - C Series

Dial-to-IP 5301-DC

Бренд: Accelerated Страницы: 26

GD200-037G/045P-4

Бренд: INVT Страницы: 266

Бренд: Samlex Europe Страницы: 33

Бренд: Jaden Страницы: 173

Бренд: Pulsar Страницы: 4

Бренд: Digitus Страницы: 4

Бренд: Goobay Страницы: 4

Бренд: Hoymiles Страницы: 2

Бренд: Microchip Technology Страницы: 24

blueplanet 87.0 TL3

Бренд: Kaco Страницы: 115

SUNNY TRIPOWER 20000TL High Efficiency

Бренд: SMA Страницы: 46

Бренд: ZeeVee Страницы: 8

Бренд: Raider Страницы: 108

Бренд: Audio Note Страницы: 79

HALF-RACK Series

Бренд: RDL Страницы: 2

Бренд: Xtender Страницы: 56

Бренд: Goobay Страницы: 28

Бренд: Sandi Electric Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды