Valleylab Force EZ - C Series Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 208

background image

Connections for Monopolar Surgery

Setup, T

e

st

s, and Adjustment

s

Force EZ-C Series Service Manual

6-5

Figure 6-3.

Bipolar connection
(handswitching instrument)

Setting the Bipolar Output

1.

To increase (+) the power, turn the Bipolar Power Control knob clockwise.
To decrease (-) the power, turn the knob counterclockwise. The maximum
power setting for bipolar output is 70 watts.

2.

To display and use the previous power setting, press the Pure and Blend
buttons simultaneously.

Connections for Monopolar Surgery

If you plan to use a footswitching monopolar instrument, you must connect a
Valleylab monopolar footswitch. You may also use a footswitch to activate a
handswitching instrument.

For most procedures, you will connect only one monopolar instrument
(handswitching or footswitching).

Caution

Set power levels to the lowest setting before testing an accessory.

handswitching
instrument

Warning

Electric Shock Hazard —

• Do not connect wet accessories to the generator.

• Ensure that all accessories and adapters are correctly connected and that no

metal is exposed.

Use only a Valleylab monopolar footswitch with the Force EZ-C Series
Electrosurgical Generator. Use of an incompatible footswitch may cause
unexpected output.

The instrument receptacles on this generator accept only one instrument at a
time. Do not attempt to connect more than one instrument at a time into a given
receptacle. Doing so will cause simultaneous activation of the instruments.

«
...
95
96
97
98
99
...
»

Содержание Force EZ - C Series

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force EZ - C Series

Бренд: YASKAWA Страницы: 44

Бренд: Yamaha Страницы: 31

Бренд: GMI Страницы: 9

Бренд: Heitronic Страницы: 8

Бренд: Intech Страницы: 4

Бренд: GoMax Electronics Страницы: 12

Бренд: Datavideo Страницы: 23

Бренд: Enerdrive Страницы: 48

Soltection RJ-1

Бренд: Vynckier Страницы: 12

Argus 2000-0370-2

Бренд: Vela Страницы: 153

Cobalt Alpha Series

Бренд: DCCconcepts Страницы: 25

Бренд: MAKINEX Страницы: 24

Бренд: oventrop Страницы: 40

ACP-09CH25AEMI/I

Бренд: M Design Страницы: 89

USB-Serial Converter REX-USB60F

Бренд: Ratoc Systems Страницы: 42

Бренд: iNels Страницы: 16

Бренд: COMPANION Страницы: 4

Бренд: Interline Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды