Valleylab Force EZ - C Series Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 208

background image

Correcting Malfunctions

T

roubleshooting

Force EZ-C Series Service Manual

7-9

Continuous monitor
interference

1.

Faulty chassis-to-ground
connections

1.

Check and correct the chassis ground
connections for the monitor and, if applicable,
for the generator.

Check other electrical equipment in the room
for defective grounds.

2.

Electrical equipment is grounded
to different objects rather than a
common ground. The generator
may respond to the resulting
voltage differences between
grounded objects.

2.

Plug all electrical equipment into line power at
the same location.

3.

Malfunctioning monitor

3.

Replace the monitor.

Interference with other
devices only when
generator is activated

1.

Metal-to-metal sparking

1.

Check all connections to the generator, patient
return electrode, and accessories.

2.

High settings used for fulguration

2.

Use lower power settings for fulguration or
select the low (desiccate) mode.

3.

Electrically inconsistent ground
wires in the operating room

3.

Verify that all ground wires are as short as
possible and go to the same grounded metal.

4.

If interference continues when the
generator is activated, the monitor
is responding to radiated
frequencies.

4.

Check with the manufacturer of the monitor.

Some manufacturers offer RF choke filters for
use in monitor leads. The filters reduce
interference when the generator is activated
and minimize the potential for an
electrosurgical burn at the site of the monitor
electrode.

Situation

Possible Cause

Recommended Action

«
...
137
138
139
140
141
...
»

Содержание Force EZ - C Series

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force EZ - C Series

VLT DeviceNet MCA 104

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 138

Бренд: Danfoss Страницы: 108

Бренд: Danfoss Страницы: 140

Бренд: Danfoss Страницы: 149

Бренд: Yamaha Страницы: 31

Бренд: OST Страницы: 2

Бренд: pro user Страницы: 60

ATLONA AT-HDVS-RX

Бренд: Panduit Страницы: 2

MAXX SST VEC054D

Бренд: Vector Страницы: 44

Бренд: ICP DAS USA Страницы: 2

Бренд: Vacon Страницы: 102

Frenic Mini FRN001C1E-2U

Бренд: Fuji Electric Страницы: 196

Бренд: INVT Страницы: 174

SC-TDC-1000 D Series

Бренд: Surface Concept Страницы: 28

Бренд: ICP CON Страницы: 8

Бренд: Omnitracs Страницы: 9

Бренд: SMA Страницы: 272

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды