Valleylab Force EZ - C Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 208

background image

Warnings, Cautions, and Notices

1-4

Force EZ-C Service Manual

Electric Shock Hazards

Servicing

Warning

Connect the generator power cord to a properly grounded receptacle. Do not use
power plug adapters.

Do not connect a wet power cord to the generator or to the wall receptacle.

To allow stored energy to dissipate after power is disconnected, wait at least five
minutes before replacing parts.

Always turn off and unplug the generator before cleaning.

Do not touch any exposed wiring or conductive surfaces while the generator is
disassembled and energized. Never wear a grounding strap when working on an
energized generator.

When taking measurements or troubleshooting the generator, take appropriate
precautions, such as using isolated tools and equipment, using the “one hand
rule,” etc.

Potentially lethal AC and DC voltages are present in the AC line circuitry, high
voltage DC circuitry, and associated mounting and heat sink hardware described
in this manual. They are not isolated from the AC line. Take appropriate
precautions when testing and troubleshooting this area of the generator.

High frequency, high voltage signals that can cause severe burns are present in
the RF output stage and in the associated mounting and heat sink hardware
described in this manual. Take appropriate precautions when testing and
troubleshooting this area of the generator.

Caution

Read all warnings, cautions, and instructions provided with this generator before
servicing.

The generator contains electrostatic-sensitive components. When repairing the
generator, work at a static-control workstation. Wear a grounding strap when
handling electrostatic-sensitive components,

except

when working on an

energized generator. Handle circuit boards by their nonconductive edges. Use an
antistatic container for transport of electrostatic-sensitive components and circuit
boards.

Notice

After installing a new low voltage power supply, verify that the voltages are
correct.

«
...
16
17
18
19
20
...
»

Содержание Force EZ - C Series

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force EZ - C Series

Бренд: Bang & Olufsen Страницы: 44

Бренд: Aksa Страницы: 50

Бренд: DK-Technologies Страницы: 90

Бренд: Kohler Страницы: 44

Бренд: Whistler Страницы: 2

blueplanet 1502xi

Бренд: Kaco Страницы: 56

Бренд: CEL-MAR Страницы: 12

Бренд: M-Audio Страницы: 24

RS-232 to Ethernet Converter ES1A

Бренд: B&B Electronics Страницы: 54

Бренд: Pulse-Eight Страницы: 2

Pure Sine PST-100S-12E

Бренд: Samlexpower Страницы: 48

AS-i CompactLineM12 AC2413

Бренд: IFM Страницы: 7

SUNNY BOY 3600TL

Бренд: SMA Страницы: 2

20km 10/100/1000WDM

Бренд: Dynamix Страницы: 2

Бренд: JDS Labs Страницы: 5

Бренд: Black Box Страницы: 18

Бренд: CYP Страницы: 16

Бренд: ToolPRO Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды