Valleylab Force EZ - C Series Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 208

background image

Periodic Safety Check

6-18

Force EZ-C Series Service Manual

Checking the Monopolar Output

Step 1 – Check the output for the cut modes

1.

Verify that the generator successfully completes the self-test as described in

Testing the Generator

in this section.

2.

Connect the test equipment for monopolar output.

a.

Connect one test cable to the left contact in the Monopolar Instrument
receptacle. Pass the test cable through the current transformer and connect
the current transformer to the voltmeter.

b.

Connect the second test cable to both pins of the Patient Return Electrode
receptacle.

c.

Connect the appropriate power resistor (refer to the table below) across
the output receptacles at the end of the test cables.

d.

Connect the monopolar footswitch to the Monopolar Footswitch
receptacle on the rear panel of the generator.

3.

Press the appropriate mode button (refer to the table below).

4.

Set the cut power (refer to the table below).

5.

Test the monopolar cut output.

a.

Press the footswitch cut pedal and, while activating the generator, note the
output on the voltmeter.

b.

Release the footswitch pedal.

c.

Based on the voltmeter setting and the current transformer you are using,
calculate and record the output current.

d.

Verify that the generator output is within the range specified in the table
below.

6.

Repeat steps 2 through 5 for each cut mode and resistor combination.

If the output is outside the specified range, calibrate the generator as described
in

Calibrating the Force EZ-C Series Electrosurgical Generator

in this

section. Then repeat this procedure. If the output for one or more cut modes
remains outside the specified range, call the Valleylab Service Center.

Generator Output (A

rms

)

Resistor

Pure Mode

(cut power @ 300 watts)

Blend Mode

(cut power @ 200 watts)

10 ohm

1.202-1.296

0.980-1.020

300 ohm

0.922-1.072

0.753-0.876

2000 ohm

N/A

0.277-0.322

3000 ohm

0.200-0.234

N/A

«
...
108
109
110
111
112
...
»

Содержание Force EZ - C Series

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force EZ - C Series

Бренд: IDK Страницы: 44

Бренд: Sima Страницы: 2

FREQROL-Z200-UL

Бренд: Mitsubishi Страницы: 120

Бренд: W&T Страницы: 12

Бренд: BSPH Страницы: 36

Pocket Inverter 100

Бренд: XPower Страницы: 38

Бренд: MG Страницы: 38

Бренд: Maplin Страницы: 3

Бренд: Ensemble Designs Страницы: 27

Бренд: PTN Страницы: 12

Single Phase Series

Бренд: Zeus Appollo Страницы: 12

Cloudy-Solar Collection IOP-USSS-12V1224-OA Series

Бренд: IO-Power Technology Страницы: 22

Бренд: BZBGEAR Страницы: 12

Бренд: SIIG Страницы: 34

Бренд: Mobotix Страницы: 44

Бренд: Peak Страницы: 37

Бренд: Lindy Страницы: 12

MAXX SST 1000 VEC049

Бренд: Vector Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды