Valleylab Force EZ - C Series Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 208

background image

Periodic Safety Check

6-14

Force EZ-C Series Service Manual

Footswitch

1.

Remove the footswitch from the generator.

2.

Disassemble the footswitch connector. Inspect the connector for damage or
corrosion.

3.

Reassemble the footswitch connector.

4.

Inspect the footswitch for damage.

5.

Reconnect the footswitch to the generator.

Power Cord

1.

Remove the power cord from the unit and ensure that it is unplugged from the
wall receptacle.

2.

Inspect the power cord for damage.

3.

Reconnect the power cord to the generator and wall receptacle.

Inspecting the Internal Components

Equipment

•

Phillips screwdriver

Procedure

1.

Verify that the generator is off by pressing the power switch off ( O ).

2.

Loosen the four screws that secure the cover to the chassis. Lift the cover off
the chassis. Set the cover aside for reinstallation.

3.

Verify that all connectors are firmly seated.

4.

Inspect each board for damaged components, wires, cracks, and corrosion.

•

If you find evidence of damage on the Control board, Display board, or
Footswitch board, replace the board. Refer to

Section 8, Control Board

, or

Section 8,

Display Board

.

•

If you find evidence of damage on the Power Supply/RF board, replace
the board only if the damage is severe. Refer to Section 8,

Power Supply/

RF Board

.

5.

Reinstall the cover on the generator. Position the cover above the chassis and
slide it down. Tighten the four screws that secure the cover to the chassis.

Caution

The generator contains electrostatic-sensitive components. When repairing the
generator, work at a static-control workstation. Wear a grounding strap when
handling electrostatic-sensitive components, except when working on an
energized generator. Handle circuit boards by their nonconductive edges. Use an
antistatic container for transport of electrostatic-sensitive components and circuit
boards.

«
...
104
105
106
107
108
...
»

Содержание Force EZ - C Series

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Force EZ - C Series

Бренд: Patton electronics Страницы: 3

blueplanet 87.0 TL3

Бренд: Kaco Страницы: 200

AVerCaster HD Duet

Бренд: Avermedia Страницы: 4

Бренд: Konig Страницы: 30

Бренд: K&S BASIC Страницы: 17

Бренд: Lika Страницы: 2

Бренд: Agilent Technologies Страницы: 70

Teranex Mini IP Video 12G

Бренд: Blackmagicdesign Страницы: 22

Бренд: Growatt Страницы: 25

Бренд: Raritan Страницы: 20

Бренд: MULTIQUIP Страницы: 62

Бренд: Uhlenbrock Elektronik Страницы: 4

Бренд: AV Access Страницы: 20

Бренд: Vicruns Страницы: 212

Бренд: Audiophony PA Страницы: 10

Бренд: Black Box Страницы: 20

Бренд: All-Power Страницы: 53

Бренд: ADF Web Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды