Stober SD6 Series Скачать руководство пользователя страница 306

Страница: 306 / 439

ID 442426.04

306

WE KEEP THINGS MOVING

Optimize

Manual SD6

Number of poles of a synchronous servo motor or asynchronous motor.

If the number of pole pairs is specified for third-party motors, the value must be

multiplied by 2 before it is entered.

Correlation between the number of poles, nominal speed n

in rpms and the

nominal frequency f

in Hz of the motor:

B10

= 2·(f

· 60/n

Entry point into field weakening.

The set value affects the dynamic properties of the drive.

Setting instructions:

•

The smaller the value the better the dynamic properties.

•

The larger the value the lower the power consumption at a given working

point.

DC link connection (peak value).

Motor voltage (chained RMS value).

Frequency of the voltage applied to the motor.

The speed determined from the motor encoder specified in

B26

. If the control

mode in

B20

does not require an encoder and none is parameterized in

B26

the speed from the motor model will be displayed.

Currently active positive torque/force limit. The reference value for

consideration on the load side is

C09

, for consideration on the motor side

B18

Currently active negative torque/force limit in reference to

B18

. The reference

value for consideration on the load side is

C09

, for consideration on the motor

side

B18

Display of the current torque or force as a percentage. Unsmoothed, in contrast

E02

. The reference value for consideration on the load side is

C09

, for

consideration on the motor side

B18

Display of the current motor speed. Unsmoothed, in contrast to

E08

. If the drive

is operated without feedback, this speed is determined by calculations using

the motor model (the actual motor speed may differ in this case from the

calculated speed).

B10

motor-poles

version 0

B92

voltage limit field weakening

version 0

E03

DC-link-voltage

version 0

E04

U-Motor

version 0

E05

f1-Motor

version 0

E15

v-motor-encoder

version 0

E65

actual positive T-max

version 0

E66

actual negative T-max

version 0

E90

actual torque/ force

version 0

E91

v-motor

version 0

Содержание SD6 Series
























































































































































































































































































































































































































































Результаты поиска

Содержание SD6 Series

Отзывы:

Бренды по названию

Популярные бренды

Stober SD6 Series, Руководство пользователя

Результаты поиска

Содержание SD6 Series

Отзывы:

Бренды по названию

Популярные бренды