Sierra Wireless DART 200 Скачать руководство пользователя страница 163

Страница: 163 / 206

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-19

Table F-4. Commands beginning with asterisk (*) (cont.)

Enable/Disable Reception of CDPD Broadcasts

Enables or disables the reception of IP broadcast packets. Refer to Chapter 4,

Broadcast and Multicast

Operation,

for more information.

Format:

AT*B0

Disable CDPD broadcast reception (default)

AT*B1

Enable CDPD broadcast reception

Result codes:

Valid argument

ERROR

Invalid argument

Enable/Disable SLIP Header Compression

Enables or disables SLIP mode header compression (V-J compression) between the MAS and the DART
modem. The setting for this parameter

must

match the compression setting in the TCP/IP stack in the

MAS for SLIP to be operational.

Format:

AT*C0

Disable SLIP TCP header compression

AT*C1

Enable SLIP TCP header compression (default)

Result codes:

Valid argument

ERROR

Invalid argument

Enable/Disable Network Operations

If PINs are required for network access, this command enables and disables access to the network.

Use of PINs can be required by the

AT\P+

or the

AT^F1

command. If required, access to the CDPD

network is denied until the proper PIN number is entered with the

AT*E+

command. Specifically the

AT\Rn

) and the Dial (

ATDx

) commands are not allowed. Once the PIN is entered, network

access is allowed until the modem is power cycled, or until access is disabled by the

AT*E-

command.

The modem becomes BLOCKED after three consecutive incorrect PIN entries are made. This condition
can be cleared with the

AT*U

command.

Format:

AT*E+<pin>

PIN entry; the user is prompted for the PIN when establishing connection to the
network. The default PIN value is 0000.

AT*E-

Disallow network access commands and require PIN reentry in order to reestablish
network connection.

Result codes:

Valid argument

ERROR

Invalid argument

BLOCKED

Command ignored

Содержание DART 200















































































































































































































Результаты поиска

Содержание DART 200

Отзывы:

Похожие инструкции для DART 200

Бренды по названию

Популярные бренды

Sierra Wireless DART 200, Руководство пользователя

Результаты поиска

Содержание DART 200

Отзывы:

Похожие инструкции для DART 200

Бренды по названию

Популярные бренды