Sierra Wireless DART 200 Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-9

Table F-2. Commands beginning with ampersand (&)

&C

Set DCD Operation

For serial ports, this command defines the usage of the data carrier detect (DCD) signal at the DART’s
RS-232 interface. This signal can be tested by the MAS application to determine if the specified
condition is true or false. Refer to Chapter 8, Application Programming,

Data and control interface,

for more information.

Format:

AT&C0

DCD is always active

AT&C1

DCD follows the state of the Connection Established condition (default)

AT&C3

DCD follows the state of RF in Range

AT&C4

DCD follows the state of Registration

NOTE:
When running in SLIP mode in a Windows/95 environment an &C1 value is required

Result codes:

OK

Valid argument

ERROR

Invalid argument

&D

Set DTR Operation

For serial ports, this command defines the DART’s response to the state of the data terminal ready
(DTR) signal at the RS-232 interface.

See

Chapter 8

, Data forwarding,

and

Data and control interface.

For both the

&D1

and

&D2

options any data remaining in the packet buffer is transmitted when the

DTR transition is accepted.

NOTE:
If &D1 or &D2 is specified auto-answer is disabled if DTR is or becomes inactive.

Format:

AT&D0

DTR is ignored (default)

AT&D1

Enter command state upon accepting an active to inactive DTR transition.

When this DTR function completes successfully the MAS receives an OK
response

AT&D2

Enter command state and terminate the connection upon accepting an active to
inactive DTR transition.

This is equivalent to executing an escape followed by an

ATH2

command.

When this DTR function completes successfully the MAS receives a NO
CARRIER

response

Result codes:

OK

Valid argument

ERROR

Invalid argument

«
...
151
152
153
154
155
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: VisionTek Страницы: 6

Бренд: UTStarcom Страницы: 57

Бренд: Kinpo Страницы: 7

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 2

Бренд: GDI COMMUNICATIONS Страницы: 21

Бренд: GDI Страницы: 21

Бренд: DECODE Страницы: 23

Бренд: Ercogener Страницы: 8

Бренд: NETGEAR Страницы: 35

ORBCOMM IDP-280

Бренд: SkyWave Страницы: 63

Бренд: Zhone Страницы: 2

TFM-560U - DATA SHEETS

Бренд: TRENDnet Страницы: 20

Бренд: Zte Страницы: 2

Бренд: MTN Страницы: 2

Бренд: xG Technology Страницы: 40

Бренд: Paradyne Страницы: 17

Бренд: Campbell Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды