Sierra Wireless DART 200 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 206

background image

DART 200 CDPD Modem User’s Guide

2 Installation and Setup

Sierra Wireless, Inc.

2-6

2.

To proceed, your PC must have the ASCII terminal emulation
program installed and active, and be attached to the CDPD modem
by the PC communications cable. To verify the setup, enter

AT

and

press

ENTER

: an

OK

response should return. To verify that the

connection is with the DART 200 and not with an internal modem,
enter

ATI

1

and press

ENTER

.

If the response is the modem software

version and date, proceed to

Basic modem personalization.

If you

fail to get that response, verify that your cable is working and that
the correct COM port is specified for the terminal emulation program
and repeat this step.

3.

If you still fail to get the AT echo and/or the

OK

, enter an

AT&V

command to display the modems communications setup, profile,
S-Registers and EID. The first three fields below the baud should be

E1, V1

and

Q0

. If the values are anything else, change to the correct

values and save the new values by entering

ATE1V1Q0&W

.

If the

AT&V

command fails, contact your DART 200 supplier for

technical assistance.

Basic modem personalization

The DART 200 requires an IP Address to be set internally before it can
be registered on the CDPD network. In addition, the side preference (A
or B) for your carrier needs to be specified. This information can be
preloaded by the carrier, but generally the carrier gives it to you upon
request. To determine if the IP Address was preloaded, refer to step 1
(below). If the IP Address was not preloaded contact your carrier to
obtain one along with the side preference (A or B), and a Domain Name
Server (DNS) IP Address.

In addition to the side preference, the DART 200 has 23 additional
operational parameters and several Status (S-)Registers to review. The
default values for these parameters and S-Registers can require changes
if they are not appropriate for your application. However, for initial setup
the default parameters (except for side preference) are adequate.

To set up the DART 200 for operation:

1.

Load the IP Address supplied by the carrier. To check if it was
preloaded, use the

AT\S?

command, as shown in this example:

at\s?
* NEI 0 = IP ADDRESS 198.225.189.032 GMID 00000
OK

* - Means the Network Entity Identifier (NEI) is active

The DART 200 in the sample has the IP Addresses already entered.
Ignore the Group Multicast Identifier (GMID) field for now.

If your modem has no IP Address, the response to the

AT\S?

command is

OK

. Enter the IP Address now, by:

•

Putting the modem into Service Provider mode with an

AT^P+51348954

command

«
...
28
29
30
31
32
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Pacific Crest Страницы: 20

Бренд: Zte Страницы: 40

Бренд: Realme Страницы: 24

Бренд: Cygnus Страницы: 6

E95-DTU433L 485-V8 Series

Бренд: Ebyte Страницы: 19

Бренд: SatExpander Страницы: 193

Бренд: Converters.TV Страницы: 7

Бренд: Swarm Страницы: 65

TJ 700x Series DOCSIS

Бренд: Terayon Страницы: 28

SmartStick SS-V1

Бренд: FAVI Страницы: 2

OfficeConnect 3CR29210

Бренд: 3Com Страницы: 54

Бренд: US Robotics Страницы: 40

Бренд: US Robotics Страницы: 58

Бренд: StarBand Страницы: 12

Бренд: Zte Страницы: 7

Бренд: E3 Страницы: 10

Бренд: QTech Страницы: 10

SMC-GPRS Series

Бренд: CalAmp Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды