Sierra Wireless DART 200 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 206

background image

PN1197-00 Revision 1.0

About This Guide

Who should read this guide

This User’s Guide is designed to assist application software developers
with setup, installation, testing, and design of applications for the Data
Access Radio Transceiver (DART) 200.

Skills required to use this guide

The reader requires a basic working knowledge of Transmission Control
Protocol/Internet Protocol (TCP/IP) and the use of the Attention (AT)
command set to use this guide.

What is in this guide

This guide provides information and assistance for both physical
installation and programming of the DART.

This guide is composed of eight chapters, eight appendixes, a glossary
and an index.

Chapter 1,

Introduction,

describes new features for version 3.0.10, how

to migrate from previous versions, and Cellular Digital Packet Data
(CDPD) network information. Also, the AT command set is summarized
in this chapter.

Chapter 2,

Installation and Setup,

provides the basic information needed

to install, setup, and test the modem on the CDPD network.

Chapter 3,

CDPD Security Features,

discusses security features such as

airlink security, authentication services, and modem security
management.

Chapter 4,

Broadcast and Multicast Operation,

discusses the CDPD

broadcast and multicast functions.

Chapter 5,

DART Supported Protocols,

discusses and gives set up

instructions for the communication protocols supported by the DART,
including User Datagram Protocol (UDP), Transmission Control
Protocol (TCP), Serial Line Interface Protocol (SLIP), and telnet. The
TCP and UDP sections include sample setups for each of the protocols.

«
...
11
12
13
14
15
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 4

Бренд: Paradyne Страницы: 16

Бренд: Paradyne Страницы: 2

Бренд: Patton electronics Страницы: 20

Бренд: Patton electronics Страницы: 8

Бренд: Patton electronics Страницы: 5

MOONLANDER 2 SCRYPT

Бренд: Futurebit Страницы: 12

NETRONIX THIAMIS 8535

Бренд: TSI Instruments Страницы: 4

Бренд: VisionTek Страницы: 6

Бренд: Abocom Страницы: 42

Бренд: Linksys Страницы: 4

Бренд: Cyta Страницы: 20

MultiConnect Cell 100 Series MTC-EV3

Бренд: Multitech Страницы: 30

Бренд: Huawei Страницы: 24

Бренд: LG Страницы: 21

Бренд: LG Страницы: 40

Бренд: LG Страницы: 63

SmartThinQ LCW-003

Бренд: LG Страницы: 353

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды