Sierra Wireless DART 200 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

Sierra Wireless, Inc.

F-24

Table F-4. Commands beginning with asterisk (*) (cont.)

*U

Unblock Modem - PIN Access

Can be used to unblock the modem if the PIN is forgotten or is entered incorrectly 3 times. The modem
is unblocked for the express purpose of entering a new PIN. Whenever this command is executed,
follow it immediately by the Set PIN command (

AT\P=

) to set a new (or restore the old) PIN value

when the current PIN is not subject to validation.

If the Set PIN command is not executed the modem remains in the unblocked state until the next power
cycle, or until a command requiring the PIN is successfully executed.

The default unblocking key is 12345678.

If the unblocking key is entered incorrectly 10 times in succession this command also becomes
BLOCKED. This condition can be cleared by using the

AT^C

command. Refer to Chapter 3, CDPD

Security Features,

Modem security management,

for more information.

Format:

AT*U+<key>

Enters the Unblocking Key

Result codes:

OK

Valid argument

ERROR

Invalid argument

BLOCKED

Command ignored

Service provider commands

The Service Provider commands provide the user with the means to
initialize the modem for use on the CDPD network, to alter protected
S-Registers, and to execute diagnostic commands.

Table F-5. Enable/Disable Service Provider mode

^P

Enable/Disable Personalization Mode

This command must be issued before any other Service Provider commands can be executed. It

puts

the DART into service provider mode and enables the other service provider commands to be executed
as well as permitting data to be stored in protected S-Registers (

see

Appendix E). The default <key> is

51348954.

Format:

AT^P-

Disable Personalization Mode

AT^P+<key>

Enable Personalization Mode

Result codes:

OK

Valid argument

ERROR

Invalid argument

BLOCKED

An invalid key was used three or more times.

«
...
166
167
168
169
170
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Patton electronics Страницы: 9

Бренд: TC Communications Страницы: 23

Бренд: NETGEAR Страницы: 2

5G WI-FI PRO MU500

Бренд: Telstra Страницы: 26

Бренд: goTenna Страницы: 22

Бренд: CTC Union Страницы: 20

Бренд: CTC Union Страницы: 46

Бренд: NetComm Страницы: 4

Бренд: Motorola Страницы: 12

Бренд: Motorola Страницы: 20

ADSL Surf USB Modem

Бренд: Acer Страницы: 14

Бренд: Abocom Страницы: 19

OfficeConnect 3C8861

Бренд: 3Com Страницы: 116

Бренд: P1 Страницы: 8

Бренд: Vyyo Страницы: 16

Бренд: Vyyo Страницы: 17

Бренд: Linksys Страницы: 14

Бренд: Linksys Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды