Sierra Wireless DART 200 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 206

background image

DART 200 CDPD Modem User’s Guide

2 Installation and Setup

Sierra Wireless, Inc.

2-4

Troubleshooting

The DART 200 is thoroughly inspected during manufacturing. There are
no end-user access items within the case of the modem. If problems
occur, check the following:

•

Power

supply

If the Power On/Registration Indicator is not flashing or glowing
solid red, check the power source for adequate voltage. The modem
requires regulated 12 V DC at 2.5 A. If the power is marginal it can
be the problem. Check the fuse (if any) in the power source, and as a
final test use a voltmeter to check for an open cable.

The DART 200 draws up to 2.5 amps under maximum power output.
The power output is a function of the modem’s distance from the
Mobile Data Base Station (MDBS). It is possible for the modem to
work well with a particular power supply in a location requiring low
power output (low current draw), and yet to fail using the same
power supply in a location requiring a high power output. Check the
amperage rating of the power supply to verify that it is adequate for
all situations.

•

Channel acquisition

If the modem does not acquire a CDPD channel (fast blinking or
solid red light), refer to

Channel acquisition

, p. 2-10, for guidelines

on how to proceed.

•

Registration

If the modem does not register refer to

Registration

, p. 2-15, for

guidelines on how to proceed.

•

Unsuccessful data transfer

If the unit registered, but application data transfer is unsuccessful,
check that the RS-232 cable is properly attached. If that does not
correct the problem, substitute a good RS-232 cable (known to
work). If that does not work, you may have a flow control problem.
Refer to

Flow control

, p. 8-12, for guidelines. Also, review the Dial

command (

ATD

) in Appendix F,

DART AT Command Set,

Auto

Answer setup, p. 8-11, and

Setup options,

p. 5-17 or

Basic UDP

setup options,

p. 5-4, setup options as appropriate.

?

?

NOTE:
To aid in
troubleshooting use an
IBM-compatible PC
with an ASCII terminal
emulator, such as
Procomm, Terminal,
Kermit, Hyperterminal,
or a Mac with White
Knight.

«
...
26
27
28
29
30
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Campbell Страницы: 3

Sierra Wireless AirLink RV50

Бренд: Campbell Страницы: 2

Бренд: Barracuda Страницы: 2

TALON UDC SERIES

Бренд: Kantronics Страницы: 23

StormPort DSL Modem

Бренд: Paradyne Страницы: 2

Бренд: Versitron Страницы: 15

USB ADSL Modem UAM700

Бренд: Abocom Страницы: 15

Бренд: SEA Страницы: 2

Бренд: NetComm Страницы: 2

Бренд: Zte Страницы: 9

Бренд: Honeywell Страницы: 87

PlusTV Hybrid Stick

Бренд: KWorld Страницы: 10

Merlin for GPRS G201

Бренд: Novatel Страницы: 54

Бренд: U.S.Cellular Страницы: 59

COR IBR1100 series

Бренд: Cradlepoint Страницы: 5

Бренд: Cradlepoint Страницы: 20

Бренд: NETGEAR Страницы: 19

Бренд: NETGEAR Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды