Sierra Wireless DART 200 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

Sierra Wireless, Inc.

F-12

Table F-2. Commands beginning with ampersand (&) (cont.)

&V

View Active Profile and S-Registers

Displays the active configuration of the DART modem. The following information is displayed:
communications port settings, the status of

AT

commands

E, V, Q, F, X, &C, &D, &E, &S, \F, \J,

\M, \N, \O, \Q, \T, *A, *B, *C, *G, *K, *R and *T

; S-Registers 0 to 99; and the EID number.

Format:

AT&V

View active profile

Result codes:

Sample output of this command can be seen in Chapter 2, Installation and Setup,

Initial testing.

&V+

View Radio Resource Status

Displays the radio resource status data for the DART’s current environment. The information
displayed is from S-Registers 100 through 126.

The format of the output is slightly different for CDPD V1.0 and V1.1. S-Registers 107 and 114
contain different data, and S-Registers 115 and 116 are not used or displayed in V1.1 mode (

see

Appendix E for details).

The data includes current channel, synchronization indicator, color code, transmit and receive signal
strength, transmit and receive block error rates, symbols in error, symbols in error rate, WASI, SPNI,
SPI, CSI, LCI, and the XID threshold and duration values for RSSI, BLER, and SER. A complete
description of these data fields is found in

Appendix E.

Format:

AT&V+

Result codes:

Sample output of this command can be seen in Chapter 2, Installation and Setup,

Channel acquisition.

&W

Save Active Profile

Saves the current configuration state and all S-Registers in nonvolatile memory. After reset or
power-up this information is restored.

Use the

&W

command following any changes to the modem setup or S-Registers to preserve the

altered settings through power cycles or reboots of the modem.

Format:

AT&W

Save active profile

Result code:

OK

Active profile saved

«
...
154
155
156
157
158
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Qtel Страницы: 28

Zlinx ZP24D-250RM-SR

Бренд: B&B Electronics Страницы: 2

MicroLink ADSL Modem

Бренд: Devolo Страницы: 41

COMSPHERE 392xPlus

Бренд: Paradyne Страницы: 285

Бренд: Hayes Microcomputer Products Страницы: 39

Бренд: Westermo Страницы: 21

MOBIIBROADBAND 4G

Бренд: iiNet Страницы: 2

Бренд: iiNet Страницы: 55

RFI 150-W-D-DD-H-1

Бренд: RF Innovations Страницы: 30

BritePort 8012-G1

Бренд: Broadxent Страницы: 55

Бренд: Four-Faith Страницы: 22

Бренд: Technicolor Страницы: 29

OfficeConnect 3C886A

Бренд: 3Com Страницы: 24

Бренд: SMC Networks Страницы: 100

Wiyana Connect 4g e-GO

Бренд: Zain Страницы: 6

Бренд: iiNet Страницы: 2

Бренд: RACOM Страницы: 34

Бренд: D-Link Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды