Sierra Wireless DART 200 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-15

Table F-3. Commands beginning with backslash (\) (cont.)

\N
(cont.)

Format:

AT\N2

B side only

AT\N3

A side preferred (default)

AT\N4

B side preferred

Choose

\N3

or

\N4

only if the modem is used in a visiting (traveling) application

Result codes:

OK

Valid argument

ERROR

Invalid argument

\O

Select PAD or Telnet Operating Mode

Allows the user to select Packet Assembler/Disassembler (PAD) mode, or telnet mode for modem
operations. Refer to

PAD operating mode,

p. 8-25, for more information.

Telnet mode logs on a user to a remote host by emulating an ASCII terminal. A telnet session uses TCP
protocol but generates additional packets both during session initiation (when terminal emulation
parameters are being negotiated), and during operation (when host echo is usually used).

PAD mode is used to communicate with specific applications or devices using TCP or UDP and usually
have less overhead than telnet. It also supports binary mode data transfers that telnet does not.

NOTE:
Telnet mode is not appropriate for telemetry applications.

To facilitate telnet setup several related profile parameters are forced by the

AT\O

command as follows:

\O1

Select telnet mode (default)

F1

Use remote echo when in online mode

\M0

Disable manual data forwarding

\T1

Enable automatic data forwarding

\O0

Select PAD mode

F0

Use local echo while in online mode

\M1

Enable manual data forwarding

\T0

Disable automatic data forwarding

Format:

AT\O0

Select PAD mode

AT\O1

Select TELNET mode (default)

Result codes:

OK

Valid argument

ERROR

Invalid argument

«
...
157
158
159
160
161
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Canon Страницы: 5

Бренд: TP-Link Страницы: 4

Бренд: Creative Страницы: 57

Бренд: Zte Страницы: 7

Бренд: BROSTREND Страницы: 13

Бренд: Zte Страницы: 36

Бренд: Zte Страницы: 22

ESTeem Horizon 216An

Бренд: EST Страницы: 104

Бренд: Dynex Страницы: 8

Бренд: DEVA Broadcast Страницы: 44

Бренд: Spectrum Страницы: 4

OnSite 1052 Series

Бренд: Patton electronics Страницы: 4

Бренд: PROLiNK Страницы: 16

Бренд: PROLiNK Страницы: 16

Бренд: Ercogener Страницы: 8

Бренд: Hughes Страницы: 116

Бренд: Ubee Страницы: 88

Бренд: ADB Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды