manualshive.com logo in svg

Sierra Wireless DART 200, Руководство пользователя


Поделиться
Скачать
background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-3

Table F-1. Commands beginning with letters (cont.)

D (cont.)

For a DART server the initial incoming datagram causes a RING message to be generated. If the auto
answer is not specified by setting S-Register 0=1, the Ring message is repeated every 10 seconds for
a total of 60 seconds.

If the call is not answered by the server (either automatically or with an 

ATA

) the client is not

informed. However, for a DART UDP server the connection request (and the attached data packet)
remains pending. If an 

ATA

 is subsequently issued, UDP generates both a RING and a CONNECT

message and accepts the pending data packet.

If the client's connection request is accepted (TCP), or validated successfully (UDP) a CONNECT
message is generated, the DART enters online mode and is ready to begin communicating with the
server. Any concatenated commands on the same line are ignored. If input is detected prior to
entering online mode the command is aborted.

The destination address can be explicitly given on the command line or can be a stored address string
retrieved from the modem’s Dial Directory (

see

 the S dial modifier below).

Format:

ATDs

s

 = dial string, plus optional dial modifiers. The dial modifier can precede (T,

P), replace (S), or follow (;) the dial string.

The dial string consists of a destination address (IP address) followed by an optional port number. It
is preceded, and optionally followed, by a dial modifier (

see

 below). The port number, if present, is

separated from the IP address by a forward slash (/).  If not present the port number for both the T
(TCP) and P (UDP) dial modifiers default to 23, the standard telnet port .

NOTE:
A DART modem in server mode only accepts calls directed to its listening port (see the *L
command). The default listening port is 2100, which is incompatible with the default dial port (23).
An example of a valid TCP dial string for port 2100 is ATDT123.456.789.2/2100.

Dial modifiers:

Dial modifiers allow additional information or actions to be specified during the connection
origination process. Dial modifiers include 

T

; 

P

; 

Sn

 and semi-colon (

;

).

T

The T modifier enables a TCP connection to be established. The configuration of
the destination address string, as described above, still applies. The T modifier is
the default setting if no modifier is specified. Refer to Chapter 5, DART
Supported Protocols, 

TCP,

 for more information on TCP operation

Format:

ATDTs     

s

 = destination address string

P

The P modifier prepares the DART for UDP communication. The configuration
of the destination address string, as described above, still applies. A CONNECT
response only means that the command was accepted, and that the addressing
information was saved to build UDP packet headers for the data that follows. To
actually communicate the destination must have a UDP server function active,
and the source must pass some application data to the DART for transmission.

If a DART defined as a server also acts as a client, the destination port number

 

for

any originated calls

 

must be different

 

from the modems listening port if

backwards compatibility was specified. Refer to Chapter 5, DART Supported
Protocols, 

UDP,

 for more information on UDP operation.

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

T-Mobile 620 Quick Start Manual preview
620
Бренд: T-Mobile Страницы: 2
Kantronics TALON UDC SERIES User Manual preview
TALON UDC SERIES
Бренд: Kantronics Страницы: 101
Olive V-ME110 User Manual preview
V-ME110
Бренд: Olive Страницы: 38
ADTRAN Total Access 1240 Installation And Maintenance Practice preview
Total Access 1240
Бренд: ADTRAN Страницы: 146
Digi XBee3 XB3M1 User Manual preview
XBee3 XB3M1
Бренд: Digi Страницы: 252
NetComm ROADSTER 56K User Manual preview
ROADSTER 56K
Бренд: NetComm Страницы: 20
UTStarcom UM175US User Manual preview
UM175US
Бренд: UTStarcom Страницы: 57
D-Link DSL-2544N Quick Installation Manual preview
DSL-2544N
Бренд: D-Link Страницы: 8
Philips SNV6520 Quick Start Manual preview
SNV6520
Бренд: Philips Страницы: 2
Philips FM02SW31/27 Specifications preview
FM02SW31/27
Бренд: Philips Страницы: 2
Philips FM02SW31/00 (Korean) Specifications preview
FM02SW31/00
Бренд: Philips Страницы: 2
Philips FM02SW10 Specifications preview
FM02SW10
Бренд: Philips Страницы: 2
Philips Active Crystals FM02SW31 Specifications preview
Active Crystals FM02SW31
Бренд: Philips Страницы: 2
Philips FM02SW00 Specifications preview
FM02SW00
Бренд: Philips Страницы: 2
Philips Active Crystals FM02SW30 Specifications preview
Active Crystals FM02SW30
Бренд: Philips Страницы: 2
Philips RESPIRONICS DreamStation Installation And Operation Manual preview
RESPIRONICS DreamStation
Бренд: Philips Страницы: 28
Philips FM02SW00 User Manual preview
FM02SW00
Бренд: Philips Страницы: 104
Philips Active Crystals FM02SW30 User Manual preview
Active Crystals FM02SW30
Бренд: Philips Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды