Sierra Wireless DART 200 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 206

background image

DART 200 CDPD Modem User’s Guide

5 DART Supported Protocols

Sierra Wireless, Inc.

5-30

•

Terminal Emulation Negotiation - S-Register 78 determines the
terminal emulation type to offer first when negotiating with the telnet
host system. The current list is:

•

0 = DEC-VT100 (default)

•

1 = DEC-VT52

•

2 = UNKNOWN

Default is for most specific first, such as 0. When the telnet session is
established and negotiation is complete, the actual terminal type chosen
is determined by using the telnet escape mode status command, or by an
appropriate command for the remote server. If UNKNOWN was
selected, the backspace and delete keys may not work correctly. If this is
the case you have two options:

1.

Use the erase character definition on the remote server. UNIX
usually uses the

tset, stty, or

printen commands to access terminal

parameters. Refer to a UNIX manual or ask the serving system
administrator.

OR

2.

Use the telnet virtual terminal erase character command to send the
erase character.

Telnet escape commands

When in a telnet session, entering a

Ctrl ^

means that telnet interprets the

next keystroke as a command. The commands include:

e

Send Telnet Virtual Terminal erase character command.

i

Send Telnet IP command (Interrupt Process).

l

Tell server you are going to local echo mode

r

Request server to perform remote echo usually responds [YES] if
there

a

Send a telnet AYT Are You There (AYT) command; Server
usually responds YES if there

b

Request Binary Mode. This is not normal, use with caution

o

Request to turn Binary Mode off

s

Print current status of telnet session. (Local parameters)

^

Send the local telnet escape character.

Any other key that follows the

^^

sequence displays a list of allowed

commands. S-Register 77 contains the telnet escape character (default is
^^ or decimal 30.

Some of the DART 200 profile parameters (

\Mn

,

\Tn,

and so on) can be

changed after logging in to the telnet host by using the DART 200’s
escape to command mode sequence (

+++

). However, do not change

S-Register values and modem profile parameters that were negotiated
with the remote host when in the connected state, since changing their
values at this point could impact client/remote host communication.
After completing your changes, return to the telnet session with the

ATO

command.

«
...
82
83
84
85
86
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: THOMSON Страницы: 48

Бренд: KaiDeng Страницы: 4

premium-line CMO 2-01

Бренд: axing Страницы: 4

Бренд: Infiniteq Страницы: 9

Бренд: MultiModem Страницы: 88

Mobile Internet Key

Бренд: Huawei Страницы: 12

Бренд: Technicolor Страницы: 3

Бренд: Fritz! Страницы: 250

CellPipe 20A-USB

Бренд: Lucent Technologies Страницы: 44

EZ Modem SMC3056EM

Бренд: SMC Networks Страницы: 45

Бренд: Hughes Страницы: 17

Бренд: Trust Страницы: 78

Бренд: M2M Страницы: 32

Бренд: Sierra Wireless Страницы: 15

Бренд: Franklin Wireless Страницы: 16

Бренд: Zte Страницы: 8

MTX-3G-JAVA series

Бренд: MTX Страницы: 109

Бренд: Zte Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды